Boya mağazası

Pony Luxury Coating M&K Pony 7000

Koşul: yeni, Üretim yılı: 2025, toplam yükseklik: 4.000 mm, toplam uzunluk: 7.000 mm, toplam genişlik: 3.000 mm, garanti süresi: 24 aylar, sıcaklık: 80 °C, hava ihtiyacı: 36.000 m³/saat, giriş voltajı: 380 V, ısıtma kapasitesi: 345 kW (469,07 bg), güç: 40 kW (54,38 bg), yakıt: sıvılaştırılmış petrol gazı (LPG), enerji tüketimi: 40 kWh, yalıtım malzemesi: Mineralwolle, izolasyon kalınlığı: 50 mm, nominal güç: 345 kW (469,07 bg), Donanım: aydınlatma, MAIN STANDARD Our spray booths are designed to meet all essential requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. The processes within the booth are managed by a PLC system, ensuring that preset values are consistently maintained. OPERATING PRINCIPLES OF THE BOOTH The processes in the booth are managed via a control panel, which governs the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passes through front filters before entering the plenum at ambient temperature. Subsequently, the air is expelled through the extraction unit. Floor filters (paint stop) capture paint particles, and the air passes through the final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues to run for approximately 15 minutes to vent out residual solvents and thinners. During this phase, fresh air from outside circulates through the booth. DRYING PROCESS In this stage, 80% of the air flowing through the booth is heated to 60°C and delivered into the booth via a distributor. As 20% of the solvents are released during drying, these are expelled with the exhaust air. Industrial coatings are typically cured at 60°C, but the booth temperature can be adjusted as required via the control panel. COOLING PROCESS After the 30-minute drying period, the coil is deactivated through the control panel, the pneumatic damper closes, and the extraction system restarts. During a 5-minute cooling phase, fresh outside air circulates within the booth; after this, the system automatically shuts down. Gedpfx Afewzmcborsbl ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels manage the functions and operation of all machines and devices installed in the booth. The control panel is made of durable galvanized sheet metal and steel profiles, and is fully enclosed for dust and moisture protection. Electrical Devices and Control Panel: • The control panel houses necessary components such as circuit breakers, fuses, signal lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the panel and motors or other electrical equipment. • Electrical wiring is designed to enable booth relocation if required. • Equipment operates on 380 V 50 Hz, while control devices use 220 V. • The booth's operating hours can be monitored on the electronic control panel for easy maintenance tracking. • Heat and timer settings for paint flashing, intermediate drying, and full drying can be easily set to the required values via the digital display on the electronic control panel. • Users can monitor and adjust drying time using the heating thermostat and the time relay.

Koşul: yeni, 90 derecede kesim alanı: yuvarlak 305 mm 90 derecede kesim alanı: kare 260 mm 90 derecede kesim alanı: dikdörtgen 350x200 mm Şerit testere uzunluğu 3375x27x0,9 mm Bant hızı 37 + 74 m/dak Gbodjd Iipxspfx Afrol Tabla yüksekliği 940 mm Toplam enerji ihtiyacı 1,5/1,8 kW Makine ağırlığı yaklaşık 0,65 t Alan ihtiyacı yaklaşık 1,5 x 1,75 x 1,9 m KAMPANYA FİYATI!!! Çift açılı metal şerit testere, hidrolik yarı otomatik GBS 305 HA-I Easy - 60° sola ve 45° sağa eğimli kesimler - Malzeme yükseklik sensörü - Bilyalı yataklı döner tabla - Yan yönde hareketli hidrolik mengenesi - Sağlam ve büyük malzeme dayanağı - Otomatik soğutma sistemi

Koşul: yeni, Üretim yılı: 2026, Fonksiyonellik: tamamen fonksiyonel, giriş akımı türü: trifaze, Painting/Spray Booth !! This is a brand new machine directly from the manufacturer. We are the producers. Photos are from previous customer installations !! Professional painting/spray booth Reinox 300×235, ideal for medium-sized components and series production. Designed for use in explosion hazard environments (EX certified), it offers high extraction performance, efficient three-stage filtration, and reliable operation for continuous use. Technical specifications: - The fan is certified for ATEX Zone 22 - Extraction area: 3000 × 1900 mm - Overall dimensions: 3100 × 2350 × 1910 mm - Dimensions are without the fan and control panel! - Fan power: 3 kW (ATEX version) - Fan extraction capacity: 16,000 m³/h (maximum 1,100 Pa) - Lighting: 2 × 36 W, ATEX certified - Power supply: 400 V, 3-phase Frequency converter: for smooth adjustment of fan power using a potentiometer on the control panel. Filtration: three-stage system Certification and documentation: CE, EX / ATEX, complete technical documentation Warranty: according to standard (12 months) Gbjdpfxjia Tauj Afrsl !!! Machines can be ordered in various individual configurations and dimensions !!! Please do not hesitate to contact us.

Koşul: yeni, Üretim yılı: 2026, Fonksiyonellik: tamamen fonksiyonel, toplam uzunluk: 5.000 mm, toplam genişlik: 3.500 mm, toplam yükseklik: 2.950 mm, iç yükseklik: 2.650 mm, iç uzunluk: 4.900 mm, iç genişlik: 3.400 mm, Donanım: kabin, Vehicle Paint Booth The vehicle paint booth is a fundamental piece of equipment in paint repair technology. It enables paintwork to be carried out under safe and comfortable conditions, while simultaneously minimizing negative effects on the surroundings and the environment. Technical data: - External dimensions: 5000 (+ supply air unit 1350 × 2900 mm) × 3500 × 2950 mm - Entrance gate: 3000 × 2600 mm (triple-leaf) - Service door: 700 × 2000 mm - Construction: made from sheet steel - Heat exchanger: standard steel - Panels: steel panels insulated with mineral wool in the walls Wall construction of the booth: - Thickness: 50 mm - Insulation: EPS polystyrene core - Colour: white Booth floor: - Booth mounted directly onto the ground/concrete slab Double ceiling: - Exterior ceiling cladding - Full-length ceiling plenum for supply air Air exchange system: - Supply air system: - Jet turbine 4 kW – 2 units - Air capacity: 26,000 m³/h - Exhaust air system: - Jet turbine 5.5 kW – 1 unit - Air capacity: 18,000 m³/h Lighting: - 8 wall-mounted lamps - Ceiling lighting: 24 LED fluorescent tubes Gedpexnpczefx Afrjbl Air heating system: - Single-stage oil burner Riello model 40 G20 - Burner control: manual - Heating-up time: 8–15 minutes Filter system: - Double-layer filter structure - High-performance air purification system with a filtration efficiency of up to 99%

Koşul: işlem için hazır (kullanılmış), çalışma genişliği 4 metre Gjdpfxew Rpxce Afrsbl iki kademeli filtrasyon: karton filtre + paint stop matı yukarı hava sirkülasyonu filtresi çalışma alanı aydınlatması fan motor gücü 4 kW İtalyan üretimi Elektrik paneli koruma sınıfı IP55 tavan aydınlatması koruma sınıfı IP65 Acil durum düğmesi (STOP) Boşaltma hunisi Yeni

Koşul: yeni, Üretim yılı: 2026, Fonksiyonellik: tamamen fonksiyonel, giriş akımı türü: trifaze, Spray Booth / Paint Booth The professional Reinox 300×185 spray/paint booth is designed for partial painting and spraying operations in industrial environments where controlled filtration and safety measures are required for work with explosive substances (ATEX compliance). Thanks to its powerful extraction system and three-stage filtration, it ensures cleanliness of the workspace even during intensive operation. !! This is always a new machine (Photos from actual customer installations). We are the manufacturer. !! Technical specifications: - Fan certified for ATEX zone 22 - Extraction surface: 3,000 × 1,400 mm - Overall dimensions (excluding fan and control panel): 3,100 × 1,850 × 810 mm - Fan power: 3 kW (ATEX compliant) - Suction capacity: 16,000 m³/h (max. 1,100 Pa) - Power supply: 400 V / three-phase - Control: frequency inverter – stepless power regulation via potentiometer on the control panel - Filtration: three-stage filter Certification & documentation: CE, ATEX, complete technical documentation Warranty: standard Machines can be ordered in various custom configurations and dimensions! Do not hesitate to contact us. Gjdpjia Ta Hsfx Afrsbl

Koşul: yeni, Üretim yılı: 2025, Fonksiyonellik: tamamen fonksiyonel, toplam yükseklik: 5.600 mm, toplam uzunluk: 11.200 mm, toplam genişlik: 5.100 mm, giriş akımı türü: trifaze, garanti süresi: 24 aylar, iç yükseklik: 4.970 mm, iç uzunluk: 11.000 mm, sıcaklık: 80 °C, iç genişlik: 5.000 mm, hava ihtiyacı: 52.000 m³/saat, giriş voltajı: 380 V, ısıtma kapasitesi: 250 kW (339,91 bg), güç: 45 kW (61,18 bg), yakıt: sıvılaştırılmış petrol gazı (LPG), giriş frekansı: 50 Hz, enerji tüketimi: 45 kWh, izolasyon kalınlığı: 50 mm, nominal güç: 250 kW (339,91 bg), maks. sac kalınlığı çelik: 2 mm, Donanım: aydınlatma, * Air Treatment Unit: The air treatment unit is a recirculation system that supplies the cabin with filtered fresh air while extracting used air during the painting process. It heats the air to 60°C, mixes 10% fresh air with the extracted air via an automatic multi-damper system, and reheats the air before it is returned to the cabin. The air is heated by a burner and a heat exchanger, both made of high-quality 304 stainless steel and located within the fresh air unit. During painting, the air is filtered twice (by front and ceiling filters) before entering the cabin. The contaminated air is also filtered twice (by intake and exhaust filters) before exiting through the exhaust unit. Air treatment units are insulated like the side panels to minimize heat loss and are protected from potential vibrations and noise by rubber seals on the covers. The exhaust air is regulated by a flap in the air outlet duct, helping to control the internal pressure of the cabin. *OPERATING PRINCIPLES OF THE CABIN: Processes in the cabin are controlled via a control panel, which manages the following steps: *PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and routed through front filters before reaching the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (overspray arrestors) capture paint particles, and the air passes through final exhaust filters before being discharged. Gjdpfx Ajwzl Hxefrjbl *FLASH-OFF PROCESS: After painting, the cabin continues to operate for approximately 15 minutes to remove residual solvents and thinners. During this phase, fresh air from outside circulates through the cabin. *DRYING PROCESS: In this phase, 80% of the air circulating through the cabin is heated to 60°C and directed into the cabin via a distributor. As 20% of the solvents are released during drying, these are expelled with the air. Industrial paints are typically dried at 60°C, but the cabin temperature can be adjusted via the control panel as needed. *COOLING PROCESS: After the 30-minute drying process, the coil is deactivated through the control panel, the pneumatic flap closes, and the extraction unit starts again. During the 5-minute cooling phase, fresh air from outside circulates through the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control cabinets manage the functions and operation of all machines and devices integrated into the cabin. The control panel is constructed from durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical equipment and control panel: • The control panel contains essential components such as circuit breakers, fuses, signal lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation when needed. • Operating equipment runs on 380 V 50 Hz, while control devices operate on 220 V.

Koşul: yeni, Üretim yılı: 2026, Bir boya atölyesi ve bir hazırlık bölgesine ayrılmış iki bölgeli bir konteyner -Dış boyutlar: 6058x2438x2591 mm -İç boyutlar: 5538x2170x2485 mm - Deniz konteyneri: 20DV - Kapı: kabin kapısına entegre - Pencere: metal koruma ızgaralı - Aydınlatma: 4 LED lamba -Montaj gerektirmez - hemen kullanıma hazırdır - Boyama kabini duvarı - tamamen ızgara Direksiyon - harici merkezi blok üzerinden otomatik; Güç - 380 V Tedarik: Eo3il2moj -fan - 3 kW - hava akış hızı - 0,7 m/s -hava akış hızı: 9500 m3/h -devridaim - kapalı devre Isıtma: -Riello 40G20 yağ brülörü -Isıtma süresi 10-15 dakika dkm3db -Maksimum sıcaklık 800°C Filtreler - ön filtre, renk durdurma filtresi, karton filtre, karbon filtre. Güvenlik: -Acil durdurma -Kapıda basınç kilidi -Sıcaklık izleme sistemi -hata göstergesi Ekipman: -16A soket Gbjdpfx Asnbd Rrefrol -hava hazırlama ekibi - Pnömatik makara

Koşul: yeni gibi (kullanılmış), DYEMANSION Tip: POWERSHOT C 2.0 Bu sistem hiç çalıştırılmamıştır. (yeni kadar iyi!!) Dyemansion Powershot C patlama kabini Toz bazlı plastik bileşenlerin yüzey dostu temizliği DYEMANSION POWERSHOT C 2.0 Yapım yılı: 2021 Basit ve etkili toz giderme için endüstri standardı Otomatik tozsuzlaştırma üretim kapasitenizi artırır Powershot C ile orta büyüklükteki bir kurulum alanı sadece on dakika içinde tozdan arındırılabilir. Parça temizliği için ihtiyacınız olan süre, ve üretiminizdeki insan gücü önemli ölçüde azaltılabilir. Bu da verimliliğinizi artırır. Powershot C ile otomatik tozsuzlaştırmaya yatırım yaparak Dört adede kadar manuel kumlama sistemi değiştirilebilir. Akıllı donanım fonksiyonları sayesinde hassas yüzey işleme Powershot C'nin kumlama kabini döner bir sepetle donatılmıştır ve paslanmaz çelikle kaplanmıştır. Farklı püskürtme nozulları ve iyonizasyon, tekrarlanabilir sonuçlar sağlar. Yumuşak, değiştirilebilir astarlı bir sepet, parçaları işlem sırasında hasara karşı korur. Aynı anda çalışan iki kumlama nozülü, döner sepete ve içerdiği parçalara dik olarak düzenlenmiştir. Bu konfigürasyon tozun etkili bir şekilde uzaklaştırılmasını garanti eder. Geliştirilmiş ergonomi ve proses kontrolü ile yüksek çalışma konforu Dokunmatik ekran ve entegre kontrol paneli ile yeni bir proses kontrol seviyesini deneyimleyin. Powershot C, kullanıcı dostu bir arayüz üzerinden çalıştırılır ve önceden yüklenmiş programlar başlatılabilir. Bireysel programlar kolayca yapılandırılabilir ve kaydedilebilir. Kullanıcı merkezli tasarım, her şeyin kolayca erişilebilir ve güvenli bir şekilde kullanılmasını sağlar. Sürekli izleme, verimli ve tekrarlanabilir bir süreç sağlar. Teknik veriler: POWERSHOT C OTOMASYON Özelleştirilmiş programlama, kontrol ve proses parametrelerinin izlenmesi kontrol paneli ve dokunmatik ekran aracılığıyla. PERFORMANS: İşlem süresi: 1 ila 40 dakika arasında değişebilir, normal verim süresi 3 ila 10 dakika Döngü başına kapasite: 3/4 EOS P396, 1x HP Jet Fusion 4200/5200'e kadar veya neredeyse 1,5 kat dolu Stratasys H350 yapı alanı Sepetin etkin hacmi 26 litre BOYUTLAR: Sistem (U x G x Y) 1700mm x 1310mm x 2030mm Çalışırken önerilen alan gereksinimi (U x G x Y) 2500mm x 2915mm x 2300mm AĞIRLIK: Sistem 480kg Güç: Güç 1kW Gereksinimler 3x400V> 1kW 50Hz 2.5A BASINÇLI HAVA: Tüketim Minimum: 2,2bar'da 1,4m³/dakika Maksimum: 5bar'da 1,8m³/dakika GÜRÜLTÜ EMISYONU: Ses seviyesi < 80dB(A) Durum: kullanılmış / ikinci el Teslimat kapsamı: (resme bakın) Gbedpfx Afstq E N Eorol (Teknik verilerdeki değişiklikler ve hatalar, teknik özellikler saklıdır!) Diğer sorularınızı telefonda yanıtlamaktan memnuniyet duyarız.

Koşul: yeni, Üretim yılı: 2026, Fonksiyonellik: tamamen fonksiyonel, giriş akımı türü: trifaze, Paint/Spray Booth !! Always a brand new machine (Photos from customer installations). We are the manufacturer. !! We offer a new Reinox 219×235 paint and extraction booth intended for professional industrial use. The booth features full EX / ATEX certification, equipped with a frequency converter for fan power adjustment, and three-stage air filtration. Suitable for painting, coating application, and vapor extraction in environments with explosion risk. Technical Specifications Manufacturer: Reinox Gedjia Taqjpfx Afrsbl Model: 219×235 - Condition: new - Fan certified for ATEX zone 22 - Supply voltage: 400 V (3~) - Fan power: 2.2 kW (EX / ATEX design) - Suction capacity: 12,000 m³/h - Maximum pressure: approx. 1,100 Pa - Lighting: 1× fixture 2×58 W (EX design) Filtration: three-stage - Suction surface dimensions: 2,190 × 2,350 mm - Overall dimensions (excluding fan and control panel): 2,295 × 2,295 × 1,910 mm Features and Benefits - Complete EX / ATEX certification – safe operation in hazardous environments - Frequency converter – smooth fan speed regulation - Three-stage filtration – high air purification efficiency - Integrated EX-certified lighting – optimal visibility during operation Reinox robust design – long service life, quiet operation, easy maintenance !!! Possibility to order machines in various custom configurations and sizes !!! Feel free to contact us.