Edgebander

BIESSE AKRON 1400

Durumu: kullanılmış, Üretim yılı: 2015, Fonksiyonellik: tamamen fonksiyonel, BIESSE Edge Banding Machine AKRON 1440-A Automatic single-sided edge banding machines for gluing and processing of straight edges using coil material (melamine, PVC, ABS, veneer) and strip material (solid wood, laminate, sliced veneer, etc.) • NC control with touch display • Automatic start of aggregate motors • Direct selection for second pass • Operating data acquisition • Software-guided maintenance TECHNICAL DATA Workpiece thickness: 10-60 mm Workpiece thickness with MFU aggregate (depending on profile): 10-35/60 mm Edge height: 14-64 mm Edge thickness (coil material): 0.4-3 mm Edge thickness (strip material)*: 0.4-10 (12) mm Workpiece overhang: 25 mm Minimum panel length: 140 mm Minimum width (with 140 mm length): 85 mm Minimum width (with 250 mm length): 50 mm Feed speed: 12 m/min Extraction*: 8x connection Ø100 mm Compressed air connection: 7 bar Glue pot capacity: approx. 2 kg * Depending on selected aggregates. - GLUING UNIT VC-511 Applies hot-melt adhesive to the workpiece, feeds the edge tape to the workpiece, automatically cuts the tape from the coil, and presses it onto the workpiece, ensuring perfect positioning. - END CUTTING UNIT IN-801 For trimming the front and rear excess edge with a 0° to 15° inclination. - DOUBLE-MOTOR MULTIFUNCTIONAL PROFILE SHAPING UNIT AR02 E Rsdpfx Abexzb Iie Sjp For corner rounding and profiling workpiece edges made of synthetic material up to a maximum thickness of 3 mm. - JOINTING MILLING UNIT RT02 Pre-mills the workpiece before glue application. Includes two 1.8 kW high-frequency motors at 12,000 rpm. - SCRAPING UNIT RB02 For post-processing of thick PVC/ABS edges. - FLAT SCRAPING UNIT RC02 Unit for removing excess glue at the joint area between edge and panel. Equipped with tracing rollers and a flat knife with operation control. - BUFFING UNIT SZ02 For cleaning and buffing the workpiece edge with fabric polishing discs. The unit automatically adjusts to the workpiece thickness. - ANTI-ADHESIVE SPRAYING DEVICE ADZ02 Precise application of anti-adhesive agent thanks to injectors activated by numerical control. - KIT PRO-GLUE The PRO-GLUE kit consists of the following components: • TEKNO-GLUE system for optimal edge bonding through: - Controlled sensing of the glue roller - Automatic retraction when feed stops - Automatic ON/OFF of the gluing section • REVERSE system to switch the glue roller between co-rotating and counter-rotating operation Electrical and mechanical preparations for use of special glue pots for POLYURETHANE glue on machines in EVA configuration. NC axis for the fine trimming unit Kit for automatic adjustment of tracing rollers and tools according to edge type and thickness. Adjustment via the control system. Pair of multi-profile cutters for the fine trimmer: 25-degree bevel milling, R=2 mm + R=1 mm, and straight profile for solid wood. NC axis for the profile shaping unit Kit for automatic adjustment of the tracer according to edge thickness. Adjustment via the control system. Function for corner processing only. NC axis for the scraping unit Kit for automatic adjustment of tracing rollers and tools according to edge type and thickness. Adjustment via the control system.

Durumu: mükemmel (kullanılmış), Biesse Stream 5.5 A Edge Banding Machine Rsdpfexxlqvsx Ab Sop Total running distance: 246,000 m Top material pressure by belt, liquids Pre-milling cutters, Glue application system, Pre-melter for PUR glue Glue pot equipped with glue discharge Pneumatic pre-cut guillotine, Pressure rollers, liquids Trim saws for precise finishing, Top and bottom milling unit with straight cutters, Top and bottom milling unit with multi-cutters Two corner rounding units Liquids Profile scraper (multi R1-R2), Cleaning fluids Flat scraper, Polishing unit The machine features NC control for milling units and a pneumatic package. Maximum workpiece height: 60mm Maximum edge thickness (roll-fed): 3mm Feed rates: 12, 18, and up to 20 m/min Machine in very good condition.

Durumu: kullanılmış, Üretim yılı: 2009, Biesse factory control system Working area on the X-axis: 3500 mm Working area on the Y-axis: 1585 mm Working stroke on the Z-axis: 350 mm Number of work zones: 2 Bar worktable Rsdpfx Abew D Dhae Sop Number of adjustable bars: 8 Number of pneumatic Bakelite bars for panel lifting: 4 3 adjustable vacuum suction cups per bar with vacuum seals to secure the panel during machining Number of 4-axis vertical electrospindles (Vector), with automatic tool changer, HSK taper 10-position rotary tool change system on the working head 24-position chain tool change system – located at the rear of the chain machine Drilling head with vertical and horizontal spindles, consisting of: - 12 vertical spindles in X - 12 vertical spindles in Y configuration - 6 horizontal spindles in X - 4 horizontal spindles in Y configuration - 1 independent sawblade for X-grooving - Carpet-style front guard and safety system - Perimeter safety fencing - Chip removal system with motorized conveyor belt - Conditioning system for cooling and cleaning the machine control unit - Vacuum pump 250 m³/h TECHNICAL DETAILS TO BE VERIFIED

Durumu: iyi (kullanılmış), Üretim yılı: 2007, makine/araç numarası: 94323, X ekseni hareket mesafesi: 3.060 mm, Y ekseni hareket mesafesi: 1.260 mm, Z ekseni hareket mesafesi: 150 mm, toplam yükseklik: 2.400 mm, toplam uzunluk: 4.400 mm, toplam genişlik: 2.800 mm, toplam ağırlık: 3.130 kg, SÜREKLİ ÇALIŞMADA BİR İŞLEME MERKEZİ satacağım CNC işleme merkezi Biesse ROVER 3.03 Redpfx Aowpthtob Sjp Wadowice'de görüntülemek için işlevsel Besleme X 3060 mm Besleme Y 1260 mm Besleme Z 150 mm Kontrol tipi CNC XP 600

Durumu: yenilenmiş (kullanılmış), Power connection: 380V, 13A, 5.5 kW main drive motor + 0.7 kW feed motor, planing width: 630 mm, Tersa cutterhead with 4 knives, stepless feed speed 6-18 m/min, star-delta switch, mechanical table height adjustment via hand lever (drive via cutterhead), fine adjustment with handwheel, mechanical digital display for planing height, 1x table roller, extraction connection: 160 mm, 1x steel infeed roller, 1x steel outfeed roller. Rodpexdl U Eofx Ab Ssp

Durumu: kullanılmış, Üretim yılı: 2018, Fonksiyonellik: tamamen fonksiyonel, SCM Olimpic K 560 Automatische Kantenanleimmaschine, Baujahr 2018, zu verkaufen! Ausstattung: - Kettenvorschubgeschwindigkeit: 12/18 m/min - Kantenstärke: 0,4–3 mm - EVA-Kleber - Fräsaggregat „RT-V“ - Leimauftragsaggregat „VC-S4.1“ - Kappaggregat „K-SEL“ - Kantenfräsaggregat „R-K“ - Eckenrundungsaggregat „ROUND X“ - Ziehschabereinheit „RAS-K“ - Poliereinheit „SP-V“ Technische Daten: - Förderbandgeschwindigkeit (zwei Stufen): 12 – 18 m/min - Min./max. Werkstückdicke: 8–60 mm - Kantenanleimung Massivholz (Stärke): 0,4–6 mm (8 mm bei HP-Ausführung) - Kantenanleimung Rollenware (Stärke): 0,4–3 mm - Maximale Fläche der angeleimten Rollenware: 135 mm² - Durchmesser der Rollenaufnahme („Teller“): 780 mm - Maximaler Kantenüberstand, relativ zum Werkstück: 2+2 mm - Mindestabstand zwischen transportierten Werkstücken: 600 mm - Mindestlänge des Werkstücks (bei min. Breite 100 mm): 140 mm - Mindestlänge der Rollenware: 180 mm - Mindestlänge der Massivholzkante: 220 mm - Mindestbreite des Werkstücks (bei min. Länge 210 mm): 95 mm (60 mm optional) - Breite des Anlagetisches: 560 mm - Tischhöhe ab Boden: 900 mm Fräsaggregat „RT-V“: - Max. Spanabnahme: 55 mm² - Max. Frästiefe: 3 mm - Min./max. Werkstückdicke: 8–45 mm (60 mm optional) - Motorleistung: 2 × 1,5 kW - Fräserdurchmesser: 100 mm Rodpfxow Sw Tke Ab Ssp - Fräserhöhe: 49 mm (64 mm optional) - Werkzeugdrehzahl: 9000 U/min

Durumu: mükemmel (kullanılmış), Üretim yılı: 2018, Fonksiyonellik: tamamen fonksiyonel, Sintra HD Yazılımı ile Akıllı Dokunmatik Sayısal Kontrol Panel yüksekliği mm 10 – 60 Katı 22mm PVC/ABS mm3 Besleme hızı 25 m/dak'ya kadar Çalışma yüksekliği C.N. tarafından elektronik olarak ayarlanabilir. Panel destek kılavuzu C.N. tarafından motorlu ve elektronik olarak ayarlanabilir. Yapışmaz grup C.N. tarafından 2 adet elektronik ayarlanabilir motorlu doğrultucu grubu Rsdpfx Abowlbxls Ssp 1 pozisyonlu makara tutucu plaka EVA sıcak eriyen tutkal için tutkal kabıyla yapıştırma ünitesi Bıçakların her hareketini takip eden dinamik emiş sistemine sahip 2 motorlu uç kesme ünitesi. C.N. tarafından elektronik olarak ayarlanabilen 2 motorlu kademeli kesme/köşe alma grubu. Yapışmazlık grubu 2 adet çok fonksiyonlu motorlu yuvarlama ünitesi (köşeleme aleti + yuvarlama aleti) C.N. tarafından üretilen elektronik olarak ayarlanabilir kenar kazıyıcı grubu. Tutkal kazıyıcı grubu Fırça grubu “SP-501” Winner 4A köprü boşaltma ile otomatik parça iade sistemi

Durumu: mükemmel (kullanılmış), Üretim yılı: 1995, Maks. Panel genişliği: 4400 mm Maks. Panel uzunluğu: 4300 mm Maks. Tahta ana testere bıçağı: 110 mm Redpfx Aomt Hhwsb Ssp Pens sayısı: 8

Durumu: kullanılmış, makine/araç numarası: 007913, Uygulanan kenar tipi: ince kenar, kalın kenar Yapıştırma sistemi: EVA, sıcak hava Birleştirme frezi: evet Çok fonksiyonlu ünite: evet Maksimum plaka kalınlığı: 60 mm Rsdpfx Abjwkf Dvs Ssp Çalışma agregaları: 7 adet

Durumu: iyi (kullanılmış), Üretim yılı: 2012, Fonksiyonellik: tamamen fonksiyonel, CNC machining center with edge banding for contoured workpieces Working dimensions for Y1 axis: X-axis: 4,300 mm X-axis pendulum machining: 1,620 mm Y-axis: 1,320 mm Working dimensions for Y2 axis (edge processing): X-axis: 3,300 mm X-axis pendulum machining: 600 mm Y-axis: 1,240 mm Worktable: 8 ATS workpiece supports, each with 3 vacuum cups 8 rear workpiece stops, programmable lowering, integrated in each support 8 workpiece stops, positioned 670 mm from the rear, integrated in each support 2 + 2 lateral workpiece stops 4 removable center stops 6 pneumatic lifting rails, programmable lowering, for positioning heavy workpieces Automatic positioning of workpiece supports and vacuum cups via EPS (Electronic Positioning System) Automatic central lubrication Division of the vacuum system into 2 separate working areas in X direction Auxiliary vacuum system for clamping templates Chip conveyor integrated into the machine table Vacuum pump 90 m³/h Rsdpfx Aoxraimjb Ssp Processing head equipment: Mounted on Z2 axis Drilling head BH 26 2L with: 16 vertical drilling spindles, individually selectable 2+2 horizontal drilling spindles, X direction 2+2 horizontal drilling spindles, X direction Grooving saw, 120 mm diameter, fixed in X direction Grooving saw, 120 mm diameter, fixed in Y direction Milling spindle 13.2 kW (11 kW S1 operation), HSK 63 F Mounted on Z1 axis Speed: 1,000 - 24,000 rpm Right and left rotation C axis 360° for adapter units Cleaning nozzle for cleaning the milled edge before the edging process 16-position tool magazine Edge banding unit for workpieces up to 60 mm thick Edgebander CNC-controlled, with 360° continuous rotation Glue application for hot-melt adhesive Double pressure roller, exchangeable and switchable Heating lamp for preheating the edge material Trimming unit for cutting the edge material at an 8° angle to the workpiece edge using circular saw blade Technical data: Plastic edge thickness 0.4 - 3 mm (*) Solid edge thickness 0.4 - 2 mm (*) (Best results with wooden edges with primer from 0.4 - 1.2 mm) Max. edge height: 64 mm Panel thickness min. 14 mm, max. 60 mm Min. internal radius: 18 mm (for edge thickness < 1 mm) Min. internal radius: 30 mm (for edge thickness 2 mm) Minimum panel size for edgebanding: 300 x 300 mm Minimum size for edgebanding interior cut-outs: 350 mm, with plastic edge max. 1 mm thickness and max. panel thickness 18 mm Edge magazine for 2 rolls, positioned outside the machine; this solution restricts pendulum machining. Roll diameter for edge material: 800 mm Safety devices: * Step mats in front of the machine * Safety fence on the right with access door Without tools Control: PC control with BIESSE WORKS ADVANCED Restart after emergency stop BIESSE WORKS office version Units: - Flush/radius milling unit - Combined profile/flat scraper blade unit - Sawing unit