Alçak şasi dorse

DINKEL 4-Achs-Jumbotieflader - doppelte Rampen

Durum: ikinci el, azami yük ağırlığı: 44.980 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: > 3 aks, ilk tescil: 09/2024, bir sonraki muayene (TÜV): 09/2025, toplam genişlik: 2.550 mm, Donanım: ABS, Our entire fleet of vehicles, including immediately and soon available models, can be found on our website. Selection of features. Complete specifications available on request. Chassis, stepped frame: * Special steel frame made from high-strength fine-grained steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle layout. Wheel covers above the axles with spray-suppression * All steel parts sandblasted * Side underrun protection made of anodised aluminum fitted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area to enable the greatest possible low-bed length in combination with AluLeg support legs instead of telescopic landing gears, max. rear swing clearance of the tractor unit approx. 2,100 mm Special superstructure with extendable rear stanchions * Self-supporting aluminum roof bow/profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear stanchions extendable to approx. 4,200 mm * Three sliding stanchions per side with rubber spring relief * Additional middle stanchion lockings in the roof bow and stowage position, actuated by pull cable and spring latch * Mechanically adjustable lifting roof, lift height approx. 400 mm, operable from both sides or one-sided without opening the opposite side or doors * Additional height adjustment approx. 480 mm in approx. 40 mm increments via stanchion adjustment * Front overlap at the bulkhead for driving under tarpaulin up to overall height approx. 4,400 mm * Four rows of approx. 150 mm stackable aluminum slats per side, 450 mm pockets at the bottom, four rows of single pockets above * Only three rows of plug-in slats in the upper deck. Spacings evenly distributed Floor * Approx. 27 mm special water-resistant bonded beech multiplex panels, rough surface * Steel sheeting in the wheel arch area * Suitable for forklift traffic according to DIN ? standard * Outer frame flush finish Brakes * WABCO air brake system with EBS according to EC Directive 71/320 EEC including PREV (Park Release Safety Valve) * Spring-type parking brake cylinders * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer axles with drum brakes, low-loader version * Air suspension with lifting and lowering function, total travel approx. 230 mm Iedpfx Anelthguo Ejig * Third and fourth axles as friction-steered trailing axles with electric and mechanical locking Twin tires * 235/75 R 17.5, -16-fold, incl. spare wheel holder, without spare wheel Paintwork * Chassis RAL 3002 red, single color * Middle stanchions, axles KTL coated black * Corner stanchions hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork in single-tone RAL color Special equipment included * ECAS air suspension, operation on the trailer * Oversize signage front and rear, galvanized, stepless telescoping with marker lights incl. bases for revolving beacons (small plates) * Additional external unlocking for sliding tarpaulin frame * 4 stanchion adapters for special outer frame profile, for locking the middle stanchions arbitrarily * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, extra-wide and extra-high version, flat hooks, tarpaulin folds, closures with ratchet/OCS * Rear left telescoping base for revolving beacon incl. light * Outer frame for machinery transport with approx. 64 lashing points in 2,000 kg, 3,000 kg, and 10,000 kg versions, according to construc

Durum: yeni, azami yük ağırlığı: 45.250 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: > 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full specification available upon request. Chassis, cranked: * Special steel frame made of high-tensile fine-grain steels, electric-welded at connection points * Well-dimensioned outer frame. 4-axle configuration * Wheel arches above the axles with spray suppression * All steel parts are sandblasted * Side underrun protection made of anodised aluminium installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the cranked area for the maximum possible low-bed length in combination with alu-leg drop supports instead of telescopic supports, max. rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special superstructure * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions extendable for loading/unloading up to approx. 4,200 mm * Three sliding stanchions per side with rubber tension relief * Additional central stanchion locks in the roof rail and parking position, via pull cable and spring bolt * DINKEL mechanical lifting roof, height-adjustable * Lifting roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the stanchions * Front overlap at the bulkhead for driving operation under tarpaulin up to total height approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the sides, lower 450 pockets, above it 4 single row pockets. In the high bed only 3 rows of slats, evenly distributed gaps Floor: * Approx. 27 mm specially water-resistant bonded beech plywood, anti-slip surface * Steel plate in wheel arch area, fork-lift truck suitable as per DIN standard * Outer frame surface flush Brakes: * WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF drum-braked axles in low-loader configuration * Air suspension with lift and lower facility, total stroke approx. 230 mm * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * Without spare wheel Lighting: * According to EC standard including LED side marker lights * Position lamps in LED version * 2 additional reversing lights * 2 working lights, inside on front wall, upper side Paintwork: * Chassis and superstructure painted in solid RAL 3002 carmine red * Centre stanchions, axles KTL-coated black * Corner stanchions hot-dip galvanised * Plastic parts black * Galvanised parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signs front and rear in galvanised, infinitely telescopic version, with mounted marker lights including base sockets for rotating beacons (small panels) * Additional unlocking of sliding roof frame from outside * 4 stanchion adapters for special outer frame profile, for securing centre stanchions as desired * PVC sliding tarpaulins, col Iisdpfx Answx Dbio Ejg