Alçak yükleyici

Fliegl DTS 300 mit Radmulden

Further information
Chassis low-loader trailer
Steel welded construction
Turntable with heavy-duty ball bearing slewing ring
Foldable rear support
2 wheel chocks with holder
Aluminum side underrun protection
Full-width rear mudflap
Quarter-shell mudguards in front of the 1st axle
1st pair of wheel recesses embedded in the deep bed lane area after the step, sloped for entry, approx. 1600 mm long at the bottom, approx. 400 mm deep. Note: The frame in the main beam area is 400 mm higher than the wheel recess.
2nd pair of wheel recesses embedded between the axles in the deep bed lane area, sloped for entry, approx. 600 mm long at the bottom, approx. 300 mm deep. Note: The frame in the main beam area is 300 mm higher than the wheel recess.
Extensions telescopic to 3,000 mm (not at rear taper)
(The track width of the construction machines or vehicles to be transported, however, must not exceed the external frame width of 2,550 mm)
Extensions telescopic to 3,000 mm, also in the wheel recesses at the bottom, foldable at the wheel recess extensions (widening not at the rear taper)
(The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm)
Wooden planks 70 mm for widening to 3000 mm
Lashing eyes low-loader
1 pair of lashing cutouts in the front longitudinal beam, recessed in the area of the step, each rated for 10 t
4 pairs of lashing holes in the external frame, each rated for 5 t (for attachment of lashing straps)
7 pairs of lashing mushrooms recessed at the top and side in the external frame, each rated for 10 t
1 x front in the step
6 x in the deep bed
First lashing eye 250 mm from the front, last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm
Drawgear - Turntable trailer drawbar
Drawbar with tested 40 mm drawbar eye
Axles + Suspension
SAF drum braked axles
Axles/chassis laser-aligned to reduce tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber mountings
Wheels and tyres
235/75 R 17.5
manufacturer's choice
Steel rims in twin arrangement, factory silver
Brake system
2-line air brake system
Spring-loaded parking brake
2 foolproof coupling heads at the front with connecting lines to the tractor unit, ABS and ALB, with ABS connector at the front, including interconnecting cable. Attention: The trailer may only be towed by towing vehicles which ensure the effectiveness of the ABS!
Electrics
24 volt, multi-chamber lights, yellow side LED lighting, 2 white position lights in front
2 white/red lane marker lights at rear
2 x 7-pin foolproof plugs at front with connecting cable
1 LED beacon with holder, switched via parking light (removable beacon)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
Front step with steel/chequer plate covering
Gjdpfsi Ri Rvsx Ad Rokc
Storage box recessed in the approach slope to the step, followed by 70 mm softwood floor, in the wheel housing area with steel/chequer plate covering
Rear slope with 70 mm softwood floor
Low-loader area including rear slope 6500 mm
Loading ramps
Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable
with wooden covering
with spring-assist lifting
Operating notes
For an axle load of 10,000 kg, a special permit is required; only indivisible loads permitted!!!
The total weight stated is technically feasible; depending on the cargo, the total weight may not be achieved while observing the permissible axle, load and fifth wheel loads. (Poor d

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.