Platform açık

Fliegl SDS 390 Baustahlmattensattel

Further Information
Chassis Semi-Trailer Forwarding
Fine-grain steel welded construction, fifth-wheel plate with interchangeable 2-inch kingpin
Vario stanchion system
4 pairs recessed into the loading area, collapsible to 2,100 mm and extendable to approx. 3,500 mm for loading. Stanchions can be locked at 100 mm intervals for an internal width of 2,100 mm to 3,000 mm, 4 pairs of divisible stanchions 600 mm + 1,200 mm, total height 1,800 mm, removable. For an internal stanchion width above approx. 2,350 mm, oversize width.
Vario bulkheads
Floor prepared for the installation of 3 bulkheads. 4 x 5 pairs of Vario stanchion pockets for plug-in bulkheads (front and rear respectively), and 1 x 3 pairs each in the center for transporting welded mesh of 2 x 5,000 mm or 2 x 6,000 mm
2 Vario bulkheads, each consisting of 1 pair of plug-in stanchions and 1 crossbeam at the top approx. 2,200 mm wide. Crossbeam extendable by 220 mm on each side, with lashing hole for securing. Height of Vario bulkhead approx. 1,900 mm, adjustable to 1,300 mm or 700 mm.
4 stanchion pockets recessed in the center of the floor for 80 x 80 mm plug-in stanchions
1 pair of supports at the bottom for front Vario bulkhead
1 pair of supports at the bottom for rear Vario bulkhead
Outer frame with slight incline, with Load-Lock profile for lashing strap hooks
14 additional pairs of lashing eyes recessed in the outer frame, 5 tons each
24 t, 2-speed landing gear, single-side operation, with straight lower section, without compensating device
Pull-out ladder at rear
Wheel chocks with holder
Aluminum side underrun protection
Galvanized steel rear underrun protection
Quarter fenders in front of and behind the axle assembly
With anti-spray mud flaps only on the last axle
Rear impact guard
8 construction steel winches with wire rope and counter hooks, 4 left and 4 right, with wire rope routing through the outer frame, 1 removable plug-on transmission for construction steel winches – supplied loose (without frame mount)
1 spare wheel holder for 1 E-wheel, with wheel fastener set
1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, can be locked with a padlock (lock not included)
1 stanchion storage box closed, open at the top, below the loading area, doors on both sides, w=450 mm / h=400/420 mm / d=2460 mm
4 lashing/stanchion rails set transversely in the floor across the full width to the outer frame (max. usable internal width between the outer plug-in stanchions approx. 2,170 mm), approx. 100 mm high. With 20 mm round steel bars, top and bottom, spaced approx. 60 mm apart (of the round steel). Bottom finishes with angle steel, half open downwards. For lashing and plugging in 80 x 80 mm stanchions.
Note: Stanchion pockets/plug-in stanchions are not designed solely for securing long loads, pipes, etc. without lashing
Iisdpfx Adoi Ri R Do Reh
Axles & Suspension
SAF disc brake axles with 430 mm disc diameter
Axle/chassis laser aligned to reduce tire wear and fuel consumption
Air suspension
1st axle with automatic lift axle, including forced lowering and starting aid, activated by braking 3x (starting aid works up to 30% axle overload and up to a max speed of 25 km/h)
Axle lift below the recommended driving height, therefore no warranty for tire damages
Brake system
2-line compressed air brake system, color-coded line routing for easy service
Spring-actuated parking brake
2 fail-safe coupling heads at the front, without connecting line
EBS, electronic braking system with EBS socket at front, no c

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.