Kullanılmış Lifepak 300 satın al (14.144)

Durumu: yeni, makine/araç numarası: b50cac2c60a813b0968994fa0, boş ağırlık: 5.700 kg, azami yük ağırlığı: 18.300 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer - Steel welded construction - Turntable with robust ball-bearing slewing ring - Foldable rear support - 2 wheel chocks with holders - Full-width rear mudguards - Prepared for extension to 3,000 mm (holes in the outer frame, not in the rear bevel) Lashing Points Low-bed - 1 pair of lashing cutouts recessed at the front in the longitudinal beam at the gooseneck, each rated for 10t - 7 pairs of lashing mushrooms recessed on top and side of the outer frame, each rated for 10t - 1x at the front on the gooseneck - 5x in the low-bed area - 1x in the rear bevel - 12 pairs of lashing holes in the outer frame, each rated for 5t (for tensioning strap hooks) - 5x gooseneck, 6x low-bed, 1x rear bevel Drawbar Hitch Turntable Trailer - Drawbar with tested 40 mm towing eye Axles & Suspension - Drum brake axles, manufacturer’s choice - Laser-aligned axles/chassis to reduce tire wear and fuel consumption - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker balance) Wheels and Tires - 235 / 75 R 17.5 Fulda - Steel twin wheels, factory silver Brake System - 2-line compressed air brake system - Spring-loaded parking brake - 2 confusion-proof coupling heads at the front, connection lines to tractor vehicle - Connection lines approx. 60 cm extended - Without ABS, but with mechanical ALB, max. 60 km/h permissible Electrics - 12 volts, multi-chamber lights, no side yellow LED lights, side reflectors - 2 white position lights front - 2 white/red lane marker lights rear - 1x 7-pole 12-volt plug at the front, with connection cable, extended by approx. 60 cm - 1 LED beacon with bracket, switched via parking light (removable beacon) - 2 pairs of illuminated, extendable warning boards up to 3,000 mm Floor Ihsdpfxei Ri Ags Abcot - Gooseneck front with steel / checker plate covering - Toolbox recessed into drive-over slope at gooseneck - Then 70 mm softwood floor, with steel / checker plate covering in wheel arch area - Rear bevel with 70 mm softwood floor - Low-bed platform including rear bevel: 5,900 mm Loading Ramps - Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable - Wood covered - Supported by spring assist Operating Instructions - For 10,000 kg axle load, a special permit is required; only indivisible loads permitted! - The specified total weight is technically possible; depending on the load, the permissible axle/support/saddle loads may not be achieved (poor tracking and maneuverability possible due to improper load distribution) Country of Registration/Plates - Country of registration: Germany - With Dekra inspection and certificate, for max. 60 km/h approval, towing vehicle LoF (for Switzerland, max. 40 km/h possible) - Prepared for two-line license plate holder - No ECE R 048 compliant contour marking / reflective strips Paintwork - Frame: DB 7350 Novagrau - 10-year warranty against rust-through - Drawbar galvanized or black, manufacturer’s choice - Loading ramps hot-dip galvanized Note: Archive images!

Durumu: yeni, makine/araç numarası: d461243f559015adca5bb372c, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis for Low-Loader Trailer Steel welded construction Turntable bogie with heavy-duty slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear spray flap Half-shell fenders on 1st axle with anti-spray flaps Additional anti-spray flaps behind 2nd and 3rd axle 1 plastic toolbox, with tray, width = 620 mm, height = 360 mm, depth = 440 mm, lockable with padlock Extendable width up to 3,000 mm Central storage compartment for wooden planks in the loading area 70 mm wooden planks for extension to 3,000 mm Lashing rings for low-loader (40 securing points) Ihsdpfx Aji Ri Dlobcet 1 pair of lashing cutouts indented in the front longitudinal beam (cranked zone), each rated for 10 t 4 pairs of lashing holes in the outer frame, each rated for 5 t (for tensioning straps) 7 pairs of lashing pins recessed in the top and side of the outer frame, each rated for 10 t 1 x at the front on the cranked zone 6 x in the low-bed First lashing ring 250 mm from front and last one max. 250 mm from rear; spacing between lashing rings not more than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, inside dimensions 70 x 40 mm, convertible to 5 t ring lashing eyes 2 additional pairs of folding lashing rings, each rated for 10 t 1 x on the cranked zone (protruding) 1 x recessed in the floor behind the last axle Drawbar / Turntable coupling Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber mounting and mechanical axle load equalization (rocker balance) Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 anti-swap coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS socket at the front, including connecting cable Make: Wabco, Knorr or Haldex Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin anti-swap plugs at the front, with connecting cable 1 LED beacon with bracket, switched via parking light (removable lamp) 2 pairs of double warning panels, LED illuminated and extendable to 3,000 mm Floor Front cranked section with steel / tread plate surface Storage box recessed in the ramp transition to cranked section Followed by 70 mm softwood floor, in wheel arch area with steel / tread plate surface Rear bevel with 70 mm softwood floor Low-loader area incl. rear bevel: 6,500 mm Loading Ramps Steel ramps, 2,800 mm length, 750 mm width, laterally adjustable Wooden inlay Hydraulically operated via tractor auxiliary drive with restrictor, operation on left side, FR Hydraulic connection with SVK coupling NW 10/3, including connecting hose Registration / Plates Country of registration: Germany 24/7 Service Hotline Prepared for two-line plate holder Contour marking with reflective tape according to ECE R 048, white on sides and red at rear Warning panel according to ECE - 70 Paintwork Frame hot-dip galvanized including passivation 15-year warranty against rust-through Drawbar galvanized or black, manufacturer’s choice Ramps hot-dip galvanized Note! These are archive images!

Durumu: yeni, makine/araç numarası: 628cde0fe99cc2d3c8eaa8dd8, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Lowbed trailer chassis Steel welded construction Turntable with robust ball bearing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Full-width rear splash guards Half-shell fenders on axle 1 with anti-spray mudflaps, anti-spray mudflaps behind axles 2 and 3 1 plastic toolbox with shelf insert, dimensions: 620 x 360 x 440 mm (W x H x D), lockable with a padlock (padlock not included) Extendable widenings up to 3,000 mm Storage compartment for timber planks in the center of the loading area 70 mm timber planks for extension to 3,000 mm Lashing eyes for low loader (40 lashing points) 1 pair of lashing cutouts in the front longitudinal beam, recessed in the cranked area, each 10 t 4 pairs of lashing holes in the outer frame, each 5 t (for attaching lashing straps) 7 pairs of recessed lashing mushrooms on top and side of outer frame, each 10 t 1 front cranked area 6 in the lowbed deck First lashing eye 250 mm from the front, last max. 250 mm from the rear, distance between lashing eyes not more than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) 2 pairs of additional folding lashing eyes, each 10 t 1 located in the cranked area (protruding) 1 recessed in the floor behind the last axle Towing equipment for turntable trailer Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles (manufacturer’s choice) Axle/chassis laser alignment to reduce tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and tires 235 / 75 R 17.5 (manufacturer’s choice) Steel rims, dual configuration, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads front, with connecting lines to the tractor unit, ABS and ALB, with ABS plug front, with connection cable Brand: Wabco or Knorr Electric system 24 volt, multi-chamber lights, yellow LED side marker lights 2 white front position lights 2 white/red lane marker lights rear 2 x 7-pin non-interchangeable plugs at front, with connecting cable 1 LED rotating beacon light with bracket, switched via parking light (removable lamp) 2 pairs of warning boards, double LED illuminated, extendable to 3,000 mm Floor Front crank area with steel / chequer plate covering Toolbox recessed in the ramp bevel to the crank Then 70 mm softwood floor, steel / chequer plate covering in wheel arch area Rear ramp bevel with 70 mm softwood floor Lowbed loading area incl. rear ramp bevel: 6,500 mm Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber-covered With spring assist Country of approval / Number plates Country of registration: Germany 24/7 service hotline Ihedsi Ri Ddopfx Abcst Prepared for two-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Warning board according to ECE-70 Painting Frame hot-dip galvanized incl. passivation 15-year warranty against corrosion Drawbar galvanized or black, as per manufacturer’s choice Loading ramps hot-dip galvanized Attention! These are archive images!

Durumu: yeni, makine/araç numarası: f8fb99947a1c19bc4d63549ff, boş ağırlık: 6 kg, azami yük ağırlığı: 17 kg, toplam ağırlık: 24 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing race Foldable rear support 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear spray flaps Half-shell fenders on the 1st axle with anti-spray mudflaps; anti-spray mudflaps behind 2nd and 3rd axles 1 plastic tool box, with shelf, w=620/h=360/d=440 mm, lockable with padlock (padlock not included) Extendable widening to 3,000 mm (not at the rear chamfer) (the track width of machines or vehicles to be transported must not exceed 2,550 mm outer frame width) Central storage compartment for wooden beams on the loading area 70 mm wooden beams for widening to 3,000 mm Lashing points on low loader 1 pair of recessed ring lashing eyes at the front on the gooseneck, each rated 5t 7 pairs of mushroom lashing points, recessed at top and side in outer frame, each rated 10t 1x at the front on the gooseneck 6x in the drop deck First lashing point 250 mm from front, last max. 250 mm from rear, distance between lashing eyes not greater than 1,100 mm 5 pairs of stake pockets recessed in side frame, internal dimension 70 x 40 mm (convertible for 5t ring lashing eyes, not included) 2 pairs of additional fold-down lashing eyes, each rated 10t 1x on the gooseneck (projecting) 1x recessed in the floor behind the last axle Trailer turntable drawgear Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum brake axles Axle/chassis laser alignment to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation (equalising rocker) Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice with M&S marking Steel wheels in twin arrangement, factory silver Brake System 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at front, with connection lines to the towing vehicle ABS and ALB, with ABS connector at front, with connection cable Brand: Wabco or Knorr Note: This trailer may only be towed by vehicles which ensure the proper functioning of the ABS! Electrics 24 Volt, multi-chamber lights, side yellow LED lighting Ihodei Riwfopfx Abcst 2 white front position lights 2 white/red rear outline marker lights 2 x 7-pin non-interchangeable plugs at front, with connection cable 1 LED rotating beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000mm Floor Gooseneck at front with steel/chequer plate covering Storage box recessed on the transition slope to gooseneck After that, 70 mm softwood floor, steel/chequer plate covering in wheel arch area Rear slope with 70 mm softwood floor Low-bed platform including rear slope 6,500 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety support, foldable underneath (prevents lateral slipping of the ramps, not in conjunction with hydraulic side ramp shift) Wooden inlay on ramps Spring lifting assistance Operating instructions At 10,000 kg axle load, an exemption permit is required, only indivisible loads possible!!! The stated total weight is technically possible; depending on the load, the gross weight may not be achievable while adhering to permissible axle, support, and kingpin loads. (Poor driving and trailing behaviour may result from incorrect load distribution) Country of registration/Plates Country of registration: Germany Approval according t

Durumu: iyi (kullanılmış), Üretim yılı: 1975, Bordür makinesi Schleiffstein - KBmL 3012-300 MACH-ID 9223 Üretici: Schleiffstein Tip: KBmL 3012-300 Üretim yılı: 1975 Şekillendirme merdaneleri R30/40/50/60/70/80/90/100 Elektrik altında çalışır durumda Dokümantasyon çizimleri mevcut Maks. iş parçası: 3000Ø Maks. sac kalınlığı: 12mm Maks. bordür yarıçapı: R-300mm Min. iş parçası: 300 Min. sac kalınlığı: 2mm Ihodpfjxcnabex Abcet Min. bordür yarıçapı: 20mm Çalışma hızı: 0 - 5000mm/dak. Güç: 30kW Uzunluk: 5000mm Genişlik: 1600mm Yükseklik: 2800mm Ağırlık: 6000kg

Durumu: kullanılmış, kilometre: 265.220 km, güç: 138 kW (187,63 bg), yakıt türü: benzin, vites türü: otomatik, ilk tescil: 07/1991, bir sonraki muayene (TÜV): 03/2023, emisyon sınıfı: euro1, renk: altın, koltuk sayısı: 5, Donanım: ABS, her tahrikli, klima, merkezi kilitleme, Mercedes Benz 300 TE 4Matic All-Wheel Drive Estate American Version Contact: Ludwig Hilmer: * Tel. * Email: L. Equipment: * Driver and passenger airbags Iedpfxsx T E Exs Abcoht * Cruise control * Electric windows front and rear * Manual air conditioning * Electrically adjustable seats for driver and passenger * Seat heating for driver and passenger * Mileage display in miles * Electric sunroof * Smoker package with ashtray and lighter * Leather armrest * Leather steering wheel * Heated rear window * Electrically adjustable passenger side mirror * Alloy wheels with winter tyres * Central locking All information without guarantee. Subject to errors and omissions. Important: New and used IVECO commercial vehicles (2.9t to 44t) and vans (up to 3.5t) in stock. New, used, and annual vehicles of all variants and weight classes available at short notice. We are happy to configure your new van/truck for you easily by phone and send you an offer tailored to all your special requests and customised solutions. Maintenance contracts, trade-ins, leasing, financing, hire purchase or classic cash purchase – with us, you will always get the right advice. Of course, we also accept your used vehicle as a trade-in at fair prices!

Durumu: yeni, Pleiger hidromotor MO 300/200 Ijdpfx Aex Uq Dcjbcjht KM No. 6257639

Durumu: kullanılmış, Üretim yılı: 1988, Robatherm RL 300 ısıtıcı, Viessmann gaz brülörü ve vana ile birlikte, temizlik kapaklı 10 m paslanmaz çelik baca dahil. Üretim yılı: 12/88. Yeni alım nedeniyle satılıyor. Tamamen çalışır durumda. Isdpfxjx Uqc Ee Abcsht

Durumu: iyi (kullanılmış), Üretim yılı: 2019, Fonksiyonellik: tamamen fonksiyonel, Ayrıca giriş ve çıkış hattını da ekliyorum. Iodpjx Rva Iofx Abcsht

Durumu: kullanılmış, Üretim yılı: 1990, Teknik detaylar: Sac kalınlığı: 8 mm Kesim alanı: 300 x 300 mm Masa boyutu: 1100 x 900 mm Gerilim: 380 V / Hz Makine ağırlığı yaklaşık: 1,7 ton Makine boyutları yaklaşık UxGxY: 1,3 x 1,2 x 1,5 m 90° sac metal parçalarını kertmek için, hidrolik olarak çalışır. Tablaya 2x cetvel 300mm 90° ofset takılmıştır. DIN 680'e göre T yuvası: a=12mm, h=21mm, b=22mm, c=14mm uzunluk = 1x 330mm ve 2x 700mm Kontrol paneli ve ayak şalteri ile çalıştırma. Ihodpfx Aou Ictbobcot *

Durumu: kullanılmış, Üretim yılı: 1968, Technical Details: Drilling capacity in St 60 - solid drilling: 40 mm Drilling capacity in cast iron: 55 mm Swing diameter over bed: Ø 22 - 2200 mm Clamping diameter approx.: Ø 100 internal / Ø 200 external mm Total power requirement: 5.0 kW Machine weight approx.: 1.2 t Ijdpfxsu Iwwzj Abcoht Machine dimensions approx. LxWxH: 1.70 x 0.80 x 1.40 m Drill spindle This machine is also usable as a milling head (as side support). Designation: Horizontal unit drilling machine with EB 40 specification: drilling Additional technical features: Headstock: - Speed range 22 - 2000 rpm - Feed range 0.025 - 0.5 U/mm - Three-jaw chuck Ø 190 mm with Ø 54 mm bore, equipped with internal jaws - Headstock bore Ø 45 mm - Drill spindle taper MK 5 Operation via control panel located on the side of the machine. By removing the chuck, the spindle can be used as a drilling unit. Max. slide adjustment 300 mm Accessories: - Various external jaws for chuck on request.

Durumu: kullanılmış, Teknik detaylar: Uzunluk: 1000 mm Genişlik: 300 mm Gerilim: 110 V Sıkıştırma yüzeyi: 1000 x 300 mm Akım: 2,9 A Makine ağırlığı yaklaşık: 204 kg Boyutlar U x G x Y: 1,2 x 0,3 x artı doğrultucu m Ihsdpfx Aou N Dy Sobcot Doğrultuculu manyetik plaka 60 mm genişliğinde ve 75 mm aralıklı 4 indüksiyon döngüsü *

Durumu: kullanılmış, Teknik detaylar: Yüz disk çapı: 318 mm Genişlik: yüz plakasının: 56 mm Geçiş maks.: Ø 54 mm Ağırlık: 17 kg Boyutlar: Ø 318 x G: 101 mm Ijdpfx Abju Nlgmocjht Teknik özellikler: - Sıkıştırma çeneleri: 4 adet, manuel besleme, sıkıştırma aralığı: dış = maks. Ø 280mm ve iç = min. Ø 40mm

Durumu: kullanılmış, Teknik detaylar: Masa çapı: 300 mm Masa yüksekliği: 250 mm Döndürme: 360 derece diyafram açıklığı: 40 mm dönme: bir tarafta 90° Makine ağırlığı yaklaşık: 126 kg Boyutlar UxGxY: 0,65 x 0,52 x 0,25 m Ayak izi: 380 x 330 mm T yuvaları: DIN 650 ve 508'e göre 4x 163 mm uzunluğunda ve 4x 135 mm uzunluğunda T yuvaları - a=12mm Ihedpfxju Nknpe Abcst - h=19mm - b=21mm - c=9mm *

Durumu: kullanılmış, Teknik detaylar: Çap: 300 mm Genişlik: 165 mm Makine ağırlığı yaklaşık: 88 kg EMAG No. 20012826 X0501 Özellikler otomati̇k kenetleme Flanş montajı Ø 140 x 13mm Ihedpfxeu Nlihs Abcot delikten 48mm Sıkıştırma cıvatası 3x M16x170mm Pmax: 60bar

Durumu: kullanılmış, Üretim yılı: 2011, Technical details: Turning length: 310 mm Ihodpfx Absw S Efzecst Swing diameter over bed: 500 mm Swing diameter over cross slide: 290 mm Distance between centers: 500 mm X-axis travel: 190 mm Z-axis travel: z1: 335 / z3: 370 mm Y-axis travel: 80 mm Spindle speed: 6,000 rpm Control: Heidenhain CNC Pilot 4290 Spindle bore: 73 mm Bar diameter: 50 mm Turret – number of stations: 12 Tool holder: VDI 30 mm Rapid traverse X + Z axes: 30 m/min Operating hours (power-on): 36,443 h Spindle hours: 8,545 h Interface: Yes Total power requirement: 20 kVA kW Dimensions chip conveyor (LxWxH): 3.2 x 0.45 x 1.5 m CNC slant-bed lathe With 3-jaw chuck Ø 160 mm including matching flange (max. speed 4,500 rpm) and two additional sets of spare jaws. 12-station turret with driven tools; Sauter disc-type turret (C-axis = 300 rpm) Main spindle torque: 95 Nm at 100%, 127 Nm at 40% Chip conveyor 450 K-1/250; year of manufacture: 2000 Electrical cabinet with Rittal cooling The machine is not equipped with a hydraulic chuck. The previous owner installed a manual chuck. The machine is for sale in non-functional condition. There is an unknown malfunction in the turret, so referencing and axis movements are not possible. As such, machining functionality is currently not possible. The machine is for sale as in need of repair! In accordance.

Üretim yılı: 1971, Durumu: kullanılmış, Teknik detaylar: Tekerlek çapı - maks.: 300 mm Modül - maks.: 5 Modül - min.: 0.5 Maksimum. iş parçası ağırlığı: 60 kg Makine ağırlığı yaklaşık: 4,0 t Makine boyutları UxGxY: 1,8 x 1,9 x 2,5 m Kontrol kabini boyutları UxGxY: No. 1: 1,95 x 0,4 x 1,95 m Kontrol kabini boyutları UxGxY: No. 2: 0,8 x 0,23 x 1,95 m Boyutlar: Egzoz hava sistemi: 1,4 x 0,7 x 0,55 m elektronik kontrollü dişli flanş taşlama makinesi modül 5'e kadar ve 240-300 mm Ø İş parçası devri başına besleme hızı sürekli değişken 0,4 - 3,2 mm maks./min. Diş sayısı: 130 / 12 Isdpfxovc An Ds Abcoht maks./min. Basınç açısı: 30° / 14°30` maks./min. 24 dişli spiral hatve: 6000 / 200 mm en fazla. diş helezon açısı, her iki taraf: 45° Öğütme solucanı hızı 1900 dev/dak. Giyinme cihazı olmadan Teçhizat: Yaklaşık. 69x vites değiştirme, boru uzatmaları ve çeşitli aletler Bu makineden iki adet satılıktır. Her iki makineye de iki ortak kontrol kabini ve bir egzoz hava sistemi aracılığıyla hava beslemesi sağlanıyor. *

Durumu: kullanılmış, Teknik detaylar: Konteyner kapasitesi: - l Gerilim: 230 / 50 V / Hz Makine ağırlığı yaklaşık: Sistem sökülmüş kg Ijdpfeu Nw Hlsx Abcsht OSMOSE SİSTEMİ Bu ünite sökülmüştür. Gösterildiği ve tarif edildiği gibi satış fiyatı üzerinden. *

Durumu: kullanılmış, Teknik detaylar: Plaka uzunluğu: 4600 mm Plaka genişliği: 1450 mm Plaka yüksekliği: 300 mm Plaka kalınlığı: 300 mm Makine ağırlığı yaklaşık: 7,2 t / plaka 2 adet bağlama plakası (fiyat plaka başına) Malzeme: çelik döküm Ihsdpfowtctgjx Abcst Yüzey ince işlenmiş DIN 650'ye göre T-kanalları: a=40; h=66; b=71; c=29 mm Orta mesafe: 300 mm 6 adet geçiş deliği Ø 41,0 mm

Durumu: kullanılmış, Teknik detaylar: Yer gereksinimi yaklaşık: 2x kutu: 0,85x0,55x0,40 / 0,10x0,55x0,4 m Aramis 3D Kamera = yüksek çözünürlüklü 3D sensör ile üst düzey uygulamalar için sağlam tasarım. Kamera çözünürlüğü 1936 x 1216 piksel Kare hızı (fps) Tam çözünürlükte 130 fps; 1/2 görüntü yüksekliğinde 24 fps; 1/4 görüntü yüksekliğinde 450 fps: Aramis Adjustable = kullanıcı dostu uygulama ile araştırma ve endüstri için modüler ve esnek ölçüm sistemi. yazılım olmadan (yalnızca üretici aracılığıyla) Fotoğrafta gösterildiği gibi satış / teslimat kapsamı. Ihedsu N Auhepfx Abcst *

Durumu: yenilenmiş (kullanılmış), Üretim yılı: 2013, Fonksiyonellik: tamamen fonksiyonel, Yeni gibi QRC 300 robot (2022 model, sadece 1258 saat), QC2 kontrol ünitesi ile (2020 model, bilgisayar 2022), bağlantı kabloları, programlama el cihazı, gaz meme sensörü, nokta editörü, zemine montaj standı dahil. Qineo Puls 350 (350 A) kaynak makinesi, tel sürme ünitesi, kaynak tığı, hortum seti, mekanik temizlik, üç ışınlı ışık bariyeri, başlatma ön seçimi, yerleştirme alanında koruma ızgarası, 1 manipülatör QR-WP-TC 1,5 kN, dönüş yarıçapı 400 mm, taşıma kapasitesi 150 kg. 3 tahrik motorunun revizyonu. 1 ışık bariyeri, 1 başlatma ön seçimi, 1 servis kapağı emniyet son anahtarlı. Bölmelerle ana şasi, yeni parlamaz boya, ana şasi. Teslimat süresi: yaklaşık 8 hafta. Ara satış hakkı saklıdır. Iedpfx Ajiyp Naobcsht

Durumu: kullanılmış, Fonksiyonellik: tamamen fonksiyonel, azami yük ağırlığı: 27.000 kg, toplam ağırlık: 8.809 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 07/2019, toplam uzunluk: 13.400 mm, toplam genişlik: 2.460 mm, süspansiyon: hava, renk: beyaz, Üretim yılı: 2019, Donanım: hidrolik direksiyon, soğutma ünitesi, tam servis geçmişi, Teknik özellikler Soğutma ünitesi - THERMO KING SLXi 300, dizel ve elektrikli Aks üreticisi - Schmitz Rotos Tam hava süspansiyonu 4 çelik çubuklu izole arka kapılar FP izoleli yan duvar, 60 mm Ihedpfjyamugox Abcst Kapak tutuculu plastik alet kutusu Plastik yakıt deposu, 245 l Elektronik fren sistemi EBS Anti blokaj sistemi ABS ROTOS SCB (disk frenler) Termometre Arka kapıda havalandırma kapağı Arka kapı için kontak anahtarı Alüminyum zeminler 2 tekerlek taşıyıcı için sepet (6+1) lastik - 385/65R22.5 (11.75x22.5) 22 kirişli çift kat Yükleme kapasitesi 33/66 euro palet Uzunluk / Genişlik / Yükseklik - 1340cm / 249cm / 265 cm Yük ile maksimum ağırlık - 39 000 kg Boş ağırlık - 8 843 kg 3 aks 36 euro palet için raf sistemi

Durumu: mükemmel (kullanılmış), Üretim yılı: 1975, Fonksiyonellik: tamamen fonksiyonel, boğaz derinliği: 450 mm, Çok iyi durumda! Dişli kutulu: Kapasite: 300 t Strok sayısı: 35 strok/dk Boğaz derinliği: 450 mm Ihedpfxsyahw No Abcjt - Pnömatik kavrama - Koç ağırlık dengeleme Koç kursu: 20 - 140 mm Koç ayarı: 80 mm Motor gücü: 30 HP

Durumu: kullanılmış, Üretim yılı: 2016, Casadei AXO 300 Plattenaufteilsäge (4.500 mm) Technische Beschreibung Arbeitshöhe: 950 mm 1 feststehender Lufttisch 2.500 x 600 mm 3 verfahrbare Lufttische 1.500 x 600 mm Zentraler Ventilator für Lufttische Fußpedal für Start/Stopp des Sägevorgangs (ideal für große Platten) Optimierte pneumatische Doppel-Führung 2.200 mm Lineare Prismaführung mit Kugellagern für 4.500 mm Sägeaggregatlänge: 4.500 mm Nutzbare Sägetiefe: 3.200 mm Längenerkennung über Lichtschranke Sägehöhe: 87 mm Max. Sägeblattdurchmesser: 350 mm Durchmesser Vorritzsägeblätter: 160 mm Vorschubgeschwindigkeit Sägeaggregat: 6–30 m/min, Upgrade auf 0–135 m/min möglich Vorschubgeschwindigkeit Schieber: 24 m/min (lt. CE-Vorgabe) Motorleistung Hauptsäge: 9,0 kW (50 Hz, S6) Motorleistung Vorritzaggregat: 1,9 kW (50 Hz, S6) Anzahl Spannzangen: 5 Absaugstutzen: 3 x 120 mm + 1 x 150 mm Maschinenabmessungen: 7.000 x 7.200 mm Steuerung: PC/API PC Control 1000 (WinNCC 12) Software: Cut I Optimierung CE-konform Isdpew E H Hbefx Abceht (Trotz größter Sorgfalt sind technische Änderungen, Irrtümer und Druckfehler sowie Preisänderungen vorbehalten. Keine Gewähr auf abgedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf.) Preise zzgl. Inserierungskosten Maschinensucher. Die besten Holzbearbeitungsmaschinen aus den Niederlanden.

Durumu: kullanılmış, Üretim yılı: 2003, Testere bıçağı çapı maks. 300 mm Iedpfx Aeud Tq Tjbceht Hız ayarı 2 seviye Makaralı konveyör dahil. Kesim maks. 120 mm Ağırlık 450 kg