Kullanılmış alçak yataklı dorse satın al (228)

Durumu: yeni, makine/araç numarası: 2428b2018baf171e60fef6740, boş ağırlık: 8.900 kg, azami yük ağırlığı: 32.100 kg, toplam ağırlık: 41.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis low-loader semi-trailer Steel welded construction, fifth wheel plate with replaceable 2” kingpin and 2 kingpin positions, 24 t, 2-speed landing gear, single-sided operation, with straight lower section, without sliding compensation Rear support foldable 2 wheel chocks with holder Aluminum side underrun protection Splash guards at rear across entire width Mudguards in front of 1st axle and behind each axle with anti-spray, according to EU regulations Extendable width up to 3,000 mm (not in rear slope) (however, the track width of the construction equipment or vehicles to be transported must not exceed 2,550 mm external frame width) Storage compartment for wooden planks in the center of the loading area 70 mm wooden planks for widening to 3,000 mm Low-loader lashing points 2 pairs of D-ring lashing eyes, each 5 t, at the front on gooseneck 11 pairs of lashing mushrooms recessed top and side in external frame, each 10 t 2 x on gooseneck 9 x distributed in low-bed deck first lashing point 250 mm from the front and last max. 250 mm from the rear, distance between lashing points no greater than 1,100 mm 8 pairs of stake pockets recessed in external frame, inside 70 x 40 mm (can be converted to 5 t D-ring lashing eyes, not included) Axles + suspension SAF drum brake axles Axles/chassis laser aligned for reduced tyre wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17.5, make at manufacturer’s discretion Steel wheels in twin configuration, factory silver Brake system 2-line compressed air brake system Color-coded piping for easy maintenance Spring-loaded parking brake EBS, electronic braking system with EBS socket at front, without connection cable Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! 2 fail-safe coupling heads at front, without connection line with lift & lower valve Axle load detection via EBS CAN bus signal, for display on the cab monitor; truck must be suitably prepared, not included (not a certified scale) Vehicle stability control system Electrics 24 Volt, multifunctional lights, side yellow LED lighting 2 white position lights in front 2 white/red lane marking lights at rear 2 x 7-pin fail-safe sockets at front, without connection cables 1 LED rotating beacon with holder, controlled via parking light (removable beacon) 2 pairs of double warning panels, LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel plate covering Storage box integrated into the transition slope to the gooseneck Then with 70 mm softwood floor, steel/chequer plate covering in wheel arch area Rear slope with 70 mm softwood floor Low-loader area incl. rear slope: 9,200 mm Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-encrusted Pjdpfx Abei Ri E Rekepl Hydraulic operation via tractor auxiliary drive with restrictor, control on left side of vehicle Hydraulic connection with SVK coupling NW 10/3, without connecting hoses Operating instructions For 10,000 kg axle load, an exceptional permit is required, only indivisible loads permitted! Special permit required if the allowable towing weight exceeds 40 t! The total weight stated is technically possible, depending on the load, the total weight may not be achievable within the permitted axle/support/kingpin load limits. (Poor driving and trailing performance possible due to improper load distribution.) For application of a special permit for regulated heavy haulage, an axle load display is requir

Durumu: kullanılmış, azami yük ağırlığı: 26.380 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2020, bir sonraki muayene (TÜV): 10/2025, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Donanım: ABS, Wiese Mega Kayar Brandalı Dorsesi, Dhollandia Rampalı 9t * Ramlı fonksiyonlu Dhollandia hidrolik lift * Tip DHLSU.90, kaldırma kapasitesi 9.000 kg, ağırlık merkezi 1.000 mm, destek ayaklarıyla * Uzaktan kumanda * Havalı süspansiyonlu ve disk frenli SAF akslar * 1. aks kaldırılabilir * Paslanmaz çelik sandıklar * Lastikler 435/50R19,5 Ppsdpfx Abjwx Trwekol Daha fazla bilgi için bizimle iletişime geçebilirsiniz.

Durumu: kullanılmış, azami yük ağırlığı: 26.100 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/2013, bir sonraki muayene (TÜV): 02/2025, yükleme alanı uzunluğu: 13.650 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.000 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Donanım: ABS, Krebs Mega Sliding Curtain Semi-Trailer with Dhollandia Tail Lift, 9-ton Capacity with Ramp Function * Recently fitted with new tarpaulins, rear and front portals newly painted * SAF axles * 1st axle liftable * 3rd axle is a trailing steering axle * Dhollandia tail lift type DHLSU.90, lifting capacity 9,000 kg, ramp function * Remote control * 3 large storage boxes * Work lights * Ice-Protect For further information, please do not hesitate to contact us. Pjdpfx Aju Em Nnebkopl

Durumu: yeni, azami yük ağırlığı: 25.300 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Ppedpfx Aov Sw E Asbkel Excerpt from the equipment. Full equipment details available on request. Gooseneck * Gooseneck in SNT design for optimized deck length * Length approx. 3,750 mm; gooseneck hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg. Suitable for tractors: 4 x 2 and 6 x 2 Tanker deck * Low bed designed as extendable tanker deck in SUPER LOW design * Length approx. 6,850 mm * with mechanical locking * Supply lines are protected in extendable beams and automatically adjust to the respective low bed length Rear running gear * In short version with closed outer frame and checker plate cover * Running gear with excavator trough, this is closed in the rear section to house air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Braking system * Make: WABCO. EBS-E according to EU regulations, WITHOUT connection cable to the tractor unit Paintwork * 6-coat treatment * Complete steel structure shot-blasted after welding * 1 layer zinc-based primer * 1 layer adhesion primer. Final coating with 2 layers of 2K (acrylic) single-color paint, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver-grey * Sidewall color: Natural Aluminum Accessories included * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations, excluding hydraulic winches. Without installation of supply connections on the tractor unit * Mounting adapter for 1 spare wheel in front of the gooseneck’s front wall * Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then every approx. 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear chamfer of the gooseneck (LC 6,000 daN) * 2-inch king pin * Hydraulic spreader beam for supporting the gooseneck on the tractor or a dolly * Air connection with air gun on the gooseneck * 1 pair of steel ramps with climbing strips and mounting bolts to bridge the low bed’s mounting hooks * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * On the outer beams of the loading area, provisions for removable load floor * Lashing rings with retaining spring approx. every 1,200 – 1,300 mm outside on the inner beams of the loading area * Lashing rings with retaining spring approx. every 1,200 – 1,300 mm outside on the outer beams of the loading area (LC 10,000 daN) * Cutouts in the upper chord of the outer beams above the lashing rings * Mechanical bolt-tab coupling from the low bed to the running gear, for deck replacement or installation of extension beams. With electro-pneumatic-hydraulic couplers * Outer beams of the low bed coated with anti-slip sand layer * 2nd driving height for upper driving position, max. ± 50 mm from normal driving position, without installation of controls from the tractor unit * 1 pair of lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Chamfered front and rear a

Durumu: kullanılmış, azami yük ağırlığı: 34.400 kg, toplam ağırlık: 57.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 06/2006, toplam genişlik: 2.750 mm, toplam yükseklik: 3.900 mm, Donanım: ABS, Faymonville 4 dingilli, sökülebilir S-boyunlu, uzatılabilir ve 4 yönlendirilebilir dingilli alçak yatak treyler Taşıma kapasitesi: 34.400 kg Tip: STBZ-4WAUB Yıl: 2006 Podpfx Abjwuhm Iskjpl - Toplam uzunluk 26 metreye kadar uzatılabilir - Hidrolik rampalar ile - Uzaktan kumandalı 4 yönlendirilebilir dingil Finansman/leasing konusunda da partnerlerimiz ile sizi memnuniyetle destekliyoruz. Tüm bilgiler garanti verilmeden sunulmuştur. Hata ve ön satış hakkı saklıdır.

Durumu: kullanılmış, azami yük ağırlığı: 29.400 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/1999, bir sonraki muayene (TÜV): 01/2026, * Reisch RPTS 35/24 alçak şasi treyler * İlk tescil: 1999 * Havalı süspansiyon * BPW ECO akslar * Kampanalı frenler * Konteyner kilitleri * 3 m'ye kadar genişletilebilir * Alt yükleme uzunluğu: 8,40 m Ppodpfx Abewyhx Iskol * Alt yükleme yüksekliği: 90 cm * Platform üzeri yükleme uzunluğu: 4,10 m * Platform yükseklik: 1,50 m * 12,50 m'ye kadar düz yükleme için çelik takoz

Durumu: kullanılmış, boş ağırlık: 6.560 kg, azami yük ağırlığı: 18.440 kg, toplam ağırlık: 25.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 09/2017, yükleme alanı uzunluğu: 13.700 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 850 mm, dingil mesafesi: 7.500 mm, renk: mavi, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, basınçlı hava freni, ek farlar, * German semi-trailer * Very good visual condition, see photos * 2-axle low loader, Jumbo TO 152 DE * Loading area: length 13,700 mm x width 2,540 mm * Loading height approx. 850 mm * Stake pockets * Multilock * Wooden loading floor * Winch with cable remote control 15,000 lbs * Long aluminium ramps 3,000 x 400 mm, laterally adjustable * ROR axles * Air suspension * Haacon spindle supports Ppjdoxu Nnwepfx Abkel * ABS + EBS * Work lights * Spare wheel * Toolbox * Drum brakes * Wheelbase 7,500 mm + 1,250 mm * Perm. gross vehicle weight 27,200 kg * Unladen weight 6,560 kg * Payload up to 20,640 kg If you require a new roadworthiness inspection (TÜV), we are happy to provide an offer through our partner workshops. Our offer is in general WITHOUT new TÜV inspection, WITHOUT new DGUV, WITHOUT new SP, WITHOUT new UVV. You can find more trucks on our website at We speak the following languages: German, English, Polish, Turkish Note: We offer and strongly recommend an inspection and evaluation of the goods to avoid any misunderstanding regarding their condition and suitability for the buyer. Viewing and inspection are possible at any time by appointment and are expressly encouraged. All information provided without guarantee. We accept no liability for errors or incorrect details in this offer. The buyer is obliged to independently verify the condition and equipment of the items/vehicles. Subject to prior sale, errors, and changes.

Durumu: yeni, azami yük ağırlığı: 73.090 kg, toplam ağırlık: 102.000 kg, dingil konfigürasyonu: 3 aks, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Below is an excerpt from the equipment list. Complete equipment specifications available upon request. Gooseneck: * Gooseneck hydraulically liftable/lowerable and detachable Ppedpfx Aexbv Auebkel * Length approx. 3,650 mm. For tractor units: 6 x 4 or 8 x 4 2-Axle Compact Front Chassis: * Hook attachments front and rear. Length: approx. 2,200 mm * Chassis width: approx. 2,850 mm Low-bed: * ATX-A low-bed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and coupling with bolt & lugs at the rear * Basic width: approx. 2,850 mm * Length: approx. 7,150 mm * Beam height: approx. 300 mm * Beam width: approx. 650 mm * Loading height approx. 450 mm with ground clearance approx. 150 mm 4-Axle Rear Chassis: * Mechanical bolt & lug coupling for attaching a low-bed at the front * Rear end crossmember * Chassis width: approx. 2,850 mm * Chassis length: approx. 5,480 mm 2-Axle Front Chassis: * Pendulum axles, all axles hydro-mechanically forced steering * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and front plug for securing in raised position * Final coating of axles: 2 layers of single-color 2-component paint in MB7350 Novagrau * Technical axle load: approx. 14,640 kg (62 km/h) * Hydraulic axle compensation 4-Axle Rear Chassis: * Pendulum axles, all axles hydro-mechanically forced steering * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and front plug for securing in raised position * Final coating of axles: 2 layers of single-color 2-component paint in MB7350 Novagrau * Technical axle load: 14,640 kg (62 km/h) * Hydraulic axle compensation Tyres: * Tyres as per manufacturer's choice (M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Complete steel structure automatically shot-blasted with a centrifugal wheel system after welding * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the complete chassis with ZINACOR 850 (85% zinc / 15% aluminium) * Final painting with two coats of 2K top coat, one color in RAL 3002 Carmine Red according to RAL system 841GL Including the following accessories: * Steel headboard, approx. 400 mm high * Plug-in aluminium side and rear panels for the gooseneck, approx. 400 mm high * 3.5 inch kingpin * Truck hydraulic connection with flow regulator (20 l/min), including gallows for suspending supply lines * The tractor unit tank must hold at least 80 liters * With MAX Trailer coupling fittings, otherwise coupling fittings to be supplied ex works by customer * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Multi-coupling hydraulic connections on the gooseneck * Front chassis with separate air connection for air tools * BEKA-MAX central lubrication for a 2-axle chassis with standard grease NLGI-2 * Preparation for mounting bolt-on container positions for 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Mounts on the outer runners of the loading platform for fitting fold-out extensions * BEKA-MAX central lubrication for a 4-axle chassis with standard grease NLGI-2 * Socket on rear chassis for cable remote control of rear steering * Rear chassis with trough * One LED beacon wi

Durumu: kullanılmış, azami yük ağırlığı: 37.640 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 04/2014, bir sonraki muayene (TÜV): 02/2026, yükleme alanı uzunluğu: 9.230 mm, yükleme alanı genişliği: 2.550 mm, yükleme alanı yüksekliği: 900 mm, yükleme alanı hacmi: 21 m³, Donanım: ABS, * 2 hatlı hava bağlantısı * Arka destek * Ön destek vinci * ABS * Kaldırma aksı * SAF akslar ----Üst yapı: Kaessebohrer LB4E EX-1 KK Alçak Yatak Düşük Dorsesi (2350mm/Boyun + 9230mm/Platform), yükleme yüksekliği yaklaşık 900mm, genişletilebilir 3.160mm'ye kadar, 12 kademede uzayabilir, toplamda 19.575mm azami uzunluk/Minimum 12.000mm, Maksimum 18.000mm. 3. ve 4. aks arka yönlendirmeli, yaklaşma rampaları - ALÜMİNYUM. Çelik/ahşap taban, sabitleme halkaları, twistlock. Satış sadece ticari müşterilere yapılmaktadır. İHRACATTA SADECE NET FİYAT ÖDENİR!!!!! TÜM BİLGİLER EKİPMAN VE AKSESUAR İÇİN GARANTİSİZ VERİLMİŞTİR. Tüm alım-satım sözleşmeleri, faturalar, proforma faturalar, siparişler ve satış görüşmeleri genel şart ve koşullarımıza tabidir (ayrıntılar künyede belirtilmiştir). Psdpfx Absw Ririjkspl

Durumu: yeni, azami yük ağırlığı: 45.250 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full specification available upon request. Chassis, cranked: * Special steel frame made of high-tensile fine-grain steels, electric-welded at connection points * Well-dimensioned outer frame. 4-axle configuration * Wheel arches above the axles with spray suppression Podpjwx Dbiefx Abkepl * All steel parts are sandblasted * Side underrun protection made of anodised aluminium installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the cranked area for the maximum possible low-bed length in combination with alu-leg drop supports instead of telescopic supports, max. rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special superstructure * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions extendable for loading/unloading up to approx. 4,200 mm * Three sliding stanchions per side with rubber tension relief * Additional central stanchion locks in the roof rail and parking position, via pull cable and spring bolt * DINKEL mechanical lifting roof, height-adjustable * Lifting roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the stanchions * Front overlap at the bulkhead for driving operation under tarpaulin up to total height approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the sides, lower 450 pockets, above it 4 single row pockets. In the high bed only 3 rows of slats, evenly distributed gaps Floor: * Approx. 27 mm specially water-resistant bonded beech plywood, anti-slip surface * Steel plate in wheel arch area, fork-lift truck suitable as per DIN standard * Outer frame surface flush Brakes: * WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF drum-braked axles in low-loader configuration * Air suspension with lift and lower facility, total stroke approx. 230 mm * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * Without spare wheel Lighting: * According to EC standard including LED side marker lights * Position lamps in LED version * 2 additional reversing lights * 2 working lights, inside on front wall, upper side Paintwork: * Chassis and superstructure painted in solid RAL 3002 carmine red * Centre stanchions, axles KTL-coated black * Corner stanchions hot-dip galvanised * Plastic parts black * Galvanised parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signs front and rear in galvanised, infinitely telescopic version, with mounted marker lights including base sockets for rotating beacons (small panels) * Additional unlocking of sliding roof frame from outside * 4 stanchion adapters for special outer frame profile, for securing centre stanchions as desired * PVC sliding tarpaulins, col

Durumu: yeni, toplam ağırlık: 43.500 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Donanım: ABS, GVN 4GVN O4 OVERWIDTH FLATBED KOC LIFT HYDRAULIC RAMP ----VEHICLE HISTORY * NEW VEHICLE 09/2025 * VIDEO AVAILABLE ON REQUEST VEHICLE EQUIPMENT EQUIPMENT AND BODY * SPARE WHEEL * FRONT STORAGE COMPARTMENT * FRONT STORAGE COMPARTMENT UNDER NECK * TOOLBOX BOTH SIDES * FIRE EXTINGUISHER HOLDER * LOAD AREA ON THE NECK * EXTENDABLE PANEL FOR OVERWIDTH LOADS * OVERWIDTH SILL Podpfexpzr Dsx Abkjpl * OVERWIDTH WARNING SIGN 4X * LASHING POINTS * ADDITIONAL SUPPORTS * FIXED HYDRAULIC FOLDING RAMPS * ELECTRIC CONNECTION FOR HYDRAULICS OF FOLDING RAMPS * TRAILER LIGHT SYSTEMS * PRESSURE GAUGE ----CHASSIS AND AXLES * OSMAN KOC AXLES SAME SPEC AS BPW AXLES * 4 AXLES * LIFT AXLE 1ST AXLE * STEERABLE/LATCHING LAST AXLE * FULL AIR SUSPENSION * DRUM BRAKES * WABCO BRAKE SYSTEM ----TYRES * ALL TYRES * 235/75 R17.5 ----DIMENSIONS * CARGO AREA DIMENSIONS * 9.55 M L x 2.55 M W (3 M W FOR OVERWIDTH) * LENGTH OF RAMPS * 3.23 M L x 0.75 M W * CARGO DIMENSIONS ABOVE NECK * 1.8 M L x 2.4 M W * NECK HEIGHT FROM GROUND * 1.4 M H * LOAD AREA HEIGHT FROM GROUND * 0.9 M H * OVERALL LENGTH WITHOUT RAMPS * 13.6 M L ----IMMEDIATELY READY FOR USE ---- * EXPORT SALE ONLY WITH A DEPOSIT (MIN. €500 - €2000) * EXPORT SALES ONLY WITH DEPOSIT MIN. €500 - €2000 ----EXPORT DECLARATION CUSTOMS EXW IN 10 MIN. (APPROVED EXPORTER) 5 DAYS, 30 DAYS PLATES, AND 17-21 DAYS AUSTRIAN PLATES EURO 1 VEHICLE RESERVATIONS ONLY VIA EMAIL FUNCTION. VERBAL RESERVATIONS ARE NOT VALID! For sales to EU and third countries, a deposit of at least €500.00 / €1,000.00 is required. (For sales to the EU and third countries a deposit/guarantee of at least €500.00 / €1,000.00 will be levied.) Subject to changes, errors, and prior sale! You can find more vehicles on our website: Sale is subject exclusively to our general terms and conditions – see website Important note – Important information: Despite careful checking of all details in our offer, errors may occur. Sometimes these are caused by transfer errors in the systems of different platform providers. We therefore point out that all information is provided without warranty and does not constitute a legal claim. Legal: This sales listing does not constitute an offer within the meaning of §145 BGB. Rather, it serves as information for initiating a contract. The information given here is without warranty and does not represent guaranteed properties.

Durumu: yeni, toplam ağırlık: 43.500 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Donanım: ABS, GVN 4GVN O4 EXTRA-WIDE FLATBED KOÇ LIFT HYDRAULIC RAMP ----VEHICLE HISTORY * NEW VEHICLE 09/2025 * VIDEO AVAILABLE ON REQUEST VEHICLE EQUIPMENT SPECIFICATION AND SUPERSTRUCTURE * SPARE WHEEL * FRONT STORAGE COMPARTMENT * FRONT STORAGE COMPARTMENT UNDER GOOSENECK * TOOLBOXES ON BOTH SIDES * FIRE EXTINGUISHER HOLDER * LOADING AREA ON THE GOOSENECK * EXTENDABLE BOARD FOR OVERSIZE LOADS * EXCESS WIDTH SIDE RAILS * OVERSIZE WARNING SIGN 4X * LASHING POINTS * ADDITIONAL SUPPORT LEGS * FIXED HYDRAULIC LOADING RAMPS * POWER CONNECTION FOR HYDRAULIC RAMPS * TRAILER LIGHT SYSTEMS * PRESSURE INDICATOR ----CHASSIS AND AXLES * OSMAN KOÇ AXLES IDENTICAL TO BPW AXLES * 4 AXLES * LIFT AXLE ON 1ST AXLE * LAST AXLE WITH LOCKABLE STEERING * FULL AIR SUSPENSION * DRUM BRAKES * WABCO BRAKE SYSTEM ----TYRES * ALL TYRES 235/75 R17.5 ----DIMENSIONS * LOADING AREA DIMENSIONS * 9.55 M LENGTH, 2.55 M WIDTH (3 M WIDTH WHEN EXTENDED FOR OVERSIZE) * RAMP LENGTH: 3.23 M LENGTH, 0.75 M WIDTH * LOADING AREA ABOVE GOOSENECK: 1.8 M LENGTH, 2.4 M WIDTH * GOOSENECK HEIGHT FROM GROUND: 1.4 M * LOADING AREA HEIGHT FROM GROUND: 0.9 M * TOTAL LENGTH WITHOUT RAMPS: 13.6 M ---- IMMEDIATELY READY FOR OPERATION ---- * EXPORT SALES ONLY WITH DEPOSIT (DEPOSIT) MIN. 500¤ - 2000¤ * EXPORT SALES ONLY WITH DEPOSIT MIN. 500¤ - 2000¤ ----EXPORT CUSTOMS DECLARATION EXW IN 10 MIN. (APPROVED EXPORTER) 5 DAYS, 30 DAYS PLATES AND 17-21 DAYS AUSTRIA PLATES EURO 1 VEHICLE RESERVATIONS ONLY VIA THE EMAIL FUNCTION. VERBAL RESERVATIONS ARE INVALID! For sales to the EU & third countries, a deposit of at least 500.00¤ / 1,000.00¤ is required. (For sales to the EU and third countries a deposit/guarantee of at least ¤500.00 / ¤1000.00 will be levied) Subject to change, errors and prior sale! More vehicles available on our homepage: Sales are exclusively subject to our terms and conditions – see homepage. Important Note – Important Information: Despite careful inspection of all details in our offer, mistakes may occur. Some errors may result from data transmission between different platform providers. Therefore, all information is provided without guarantee and is not legally binding. Legal: This sales listing does not constitute an offer according to §145 BGB (German Civil Code). Rather, it is information for the initiation of a contract. The information provided here is without guarantee and therefore does not constitute warranted characteristics. Psdpfx Absxpzrwjkopl

Durumu: kullanılmış, Fonksiyonellik: tamamen fonksiyonel, boş ağırlık: 6.000 kg, azami yük ağırlığı: 29.300 kg, toplam ağırlık: 35.700 kg, ilk tescil: 01/1998, Reisch RPTS 35/24 alçak yükleyici römork Psdpfx Abjxg Hw Tekjpl EZ 1998 3 eksen hava yaylı kampana frenler BPW ECO aksları Ağırlığı: 6000 kg GGW: 35700 kg yük kapasitesi 29300 kg toplam uzunluk 13.25 m yükleme yüksekliği 90 cm Alt yükleme uzunluğu: 9,60 m Üstten yükleme uzunluğu: 3,95 m üstteki yükleme yüksekliği 145 cm

Durumu: kullanılmış, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 11/2004, bir sonraki muayene (TÜV): 08/2026, * Müller Mitteltal TS3 alçak şasi treyler (dorseli) * İlk tescil: 11/2004 * 3 aks * Havali süspansiyon * Gigant akslar * Hidrolik uzun rampalar, kaydırılabilir ve katlanabilir * Yatak genişliği 2,50 m'den 3,0 m'ye kadar artırılabilir * Yükleme uzunluğu: 8,50 m, yükseklik: 0,85 m * Boyun kısmında yükleme uzunluğu: 3,40 m, yükseklik: 1,50 m * Destek ayakları Ppedpfjw Tgl Eox Abkjl * Boş ağırlık: 10.260 kg * Teknik toplam ağırlık: 47.000 kg * Muayene geçerlilik: 08/2026'ya kadar * Genel muayene: 02/2026'ya kadar geçerli

Durumu: yeni, azami yük ağırlığı: 38.953 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Gross vehicle weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3,850 mm Fifth wheel height loaded: 1,200 mm Loading platform length: 9,300 mm Extendable by: 0 mm Axle spacing: 1,360 mm Steering angle radius (rear): 2,300 mm Loading height at max. load: 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical Description Gooseneck: Gooseneck with chamfered front corners at 45° and rear taper of approx. 750 mm x 10°. Ppedpfx Aeg Sk Trobkol 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8°. 6 pairs of folding lashing rings facing outward (LC 5,000 daN). 2 pairs of folding lashing rings facing outward (LC 10,000 daN). 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN). Cut-outs in the outer frame of the loading platform for attaching tensioning straps. (LC 2,000 daN). Hardwood flooring approx. 48 mm thick, above the axles fitted with chequer-plate covering. Ramps: Two-piece steel ramps: One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically foldable ramp sections, hydraulic lifting device and can be hydraulically adjusted laterally. Maximum load per pair: 40,000 kg Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R 17.5 tyres as per manufacturer's selection. Axles: SAF axles, air-suspended, with drum brakes, featuring lift/lower function. Last axle is force-steered with electro-magnetic reverse lock, activatable via reverse gear or manually. Axle tools. Brake System: Brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit. Steel Construction: Steel construction made from high-strength fine-grained steel. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: Premium and durable corrosion protection via sandblasted welded frame, primed with 2-component (2K) zinc dust primer. High-quality single-tone 2-component (2K) top coat in RAL colours of your choice. Rear metalized and painted in RAL 9010 (pure white). Metallic paint not possible. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets. ISO-compliant connections. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories Included 2" king pin One galvanized steel front bulkhead approx. 400 mm high. At the galvanized front connection strip yellow/red airline couplings. 4 wheel chocks with holder on the front bulkhead (± 5kg). Cable for supplying electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long, max. 250A) between semi-trailer and tractor unit, with plug connection (ANDERSON-ANDERSON). Galvanized folding supports under the rear slope of the loading platform. Bracket for a rotary beacon at the rear of the trailer. Control valves for the ramps installed on right-hand side of trailer (± 4kg). Yellow reflective tape according to EU regulations on the sides and rear of the trailer. Electro-hydraulic unit mounted at the rear under the loading

Durumu: yeni, toplam ağırlık: 58.000 kg, Üretim yılı: 2025, Low-bed semi-trailer MAX100 4 A 8.60 U Technical Data Speed: 80 km/h Gross Vehicle Weight: 60,800 kg Fifth Wheel Load: 18,000 kg Axle Load: 42,800 kg Tare Weight: Payload: Gooseneck Length: 3,850 mm Loaded Fifth Wheel Height: 1,250 mm Loading Platform Length: 8,600 mm Extendable by: 5,400 mm Axle Spacing: 1,360 mm Steering Radius (rear): 2,300 mm Loading Height at Max. Load: 860 mm Overall Width: 2,540 mm Suspension Stroke: -55/+145 mm Technical Description Gooseneck With 45° chamfered front corners and rear chamfer approx. 760 mm x 10° 3 pairs of lashing rings (LC 5,000 daN) 30 mm thick hardwood floor Extendable loading platform With rear bevel approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings (LC 5,000 daN) 3 pairs of outward-folding lashing rings (LC 10,000 daN) 1 pair of flush-mounted lashing rings at the front of the loading platform (LC 10,000) Approx. 48 mm thick hardwood flooring, chequer plate above the axles Ramps Two-part steel ramps One pair of galvanized, two-part steel ramps, approx. 2,750 + 1,400 mm x 800 mm with approx. 48 mm hardwood flooring Ramp sections hydraulically lifted and folded in, hydraulic lift and hydraulically adjustable position Max. load per pair: 40,000 kg Tyres 235/75 R 17.5 Brake System compliant with EU regulations, with EBS-E (4S3M) Without connection lines to the tractor unit Paintwork First-class, long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by 2-component zinc dust primer High-quality 2-component (2K) top coat, single colour, in RAL shades of choice Rear section metallized and painted in RAL 9010 (Pure White) Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24t Lifting capacity (50t test load) Steel construction made from high-strength fine-grained steels. Steel Qualities: Steel construction made from high-strength fine-grained steel S355J2+N/S355MC (Yield Strength 355MPa) S690QL/S700MC (Yield Strength 690MPa) Electrical System according to EU regulations, lighting: LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets Connection as per ISO. 24N IS0-1185 24S IS0-3731 15-pin IS0-12098 Accessories included: One galvanized steel headboard approx. 400 mm high 2" king pin 4 wheel chocks with holders on the headboard One holder for revolving beacon at rear of trailer SAF axles, two rigid axles, one self-steering axle, air suspension, with drum brakes, with raise/lower function The self-steering axle with electromagnetic reverse lock, can be activated by reverse gear or manually Axle tools included Support for ALU approach ramps at the rear of the gooseneck Galvanized folding supports under the loading platform chamfer Ppjdpfx Ajg Sk T Dsbkol Mechanical safety lock for the loading platform extension One spare wheel with holder in front of the headboard Yellow reflective tape as per EU regulations on sides, extension, and rear of trailer At the front galvanized connector strip, yellow-red air couplings On gooseneck and rear apron left and right, mounts for warning plates, including sockets A mudflap at the rear of the trailer Manual and description On the gooseneck: Plug-in aluminium sideboards and rear wall, approx. 2,440 x 400 mm (LxH) Rear galvanized stanchions are removable Body length approx. 2,560 mm, +/- 46 kg 3 pairs of WADER container locks in the loading platform for a 20', 30', or 40' container (±30 kg) 6 pairs of pockets for plug-in stanchions

Durumu: yeni, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Further information here: Ppodpfx Aov D Abmsbkol

Durumu: yeni, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2025, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Gross weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Loaded saddle height: 1,200 mm Rear steering radius: 2,300 mm Loading platform length: 6,850 mm Extendable by: 5,500 mm Loading height at maximum load: 350 mm Chassis length: 2,600 mm Rear chassis loading height at max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Overall width: 2,540 mm Gross weight depends on fifth wheel load. Lowbed: Lowbed with external beams, extendable version "SUPER LOW" design, length approx. 6,850 mm. Lowbed with fixed hardwood floor approximately 40 mm thick and mechanical locking device. Supply lines are protected inside the extendable beams and automatically adjust to the respective lowbed length. 5 pairs of lashing rings, foldable outward (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear chassis: Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at rear. 2 pairs of lashing rings, foldable outward (LC 10,000 daN). 1 pair of lashing rings, flat in the trough (LC 8,000 daN + 5,300 daN). 2 pairs of pocket sockets for stanchions 100 x 50 mm in the external frame. Gooseneck: Gooseneck in SNT design to optimize usable platform length, length approx. 3,785 mm. Gooseneck hydraulically lift/lowerable and detachable. Technical fifth wheel load: 23,000 kg For tractor units: 4x2, 6x2, and 6x4 PENDLE-AXLE: “PENDLE-AXLE”, all axles hydro-mechanically forced steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and plug pins for securing in raised position. Axles finished with two coats of 2-component paint, single color "FAY-Grey-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tools. Brake system: Brake system in accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit. Electrical system: Electrical system according to EU regulations, 24V lighting ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connection strip with 24N, 24S, and 15-pin sockets. Connection according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Ppsdsizu Nwopfx Abkjl Steel construction: Steel construction made of high tensile fine-grained steels. Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Painting: Premium, long-lasting corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer. Premium two-component (2K) topcoat in one RAL color of your choice. Rear section metallized and painted in RAL 9010 (Pure White). No metallic paint possible. Tyres: Tyres 245/70 R 17.5 3PMSF Manufacturer’s choice. Load index (146/146F). Prepared for fitting of bolt-on container positions for 1x 20' or 1x 40' container on the external beams. Without container locks. • 2” king pin • Galvanized steel front wall approx. 400 mm high • 1 spare wheel with holder in front of the front wall • 2 wheel chocks with holder on the front wall • Yellow-red air couplings on the galvanized connection strip at the front. Remote steering from front and rear via cable remote control with pushbuttons, with single-track axle monitoring (without installation in the tractor unit). Hydraulic connections from the gooseneck to the lowbed

Durumu: yeni, azami yük ağırlığı: 36.461 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.480 mm, toplam yükseklik: 860 mm, Üretim yılı: 2025, Technical Description Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Pedpfxjw Dl Hws Abkjpl 30 mm thick hardwood flooring. Loading Area: Hydraulically liftable and lowerable platform after the gooseneck, approx. 2,800 mm in length, with rear taper approx. 1,000 mm x 8°. 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN). 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN). 1 pair of foldable lashing rings to the inside on the front central beam (LC 10,000 daN). Grating floor covering C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles tread plate covering. Two-Piece Steel Ramps: One pair of galvanized two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating covering C40/5 (point load 8 t on an area of 20 x 20 cm). Ramps with hydraulically folding ramp sections and hydraulic lifting mechanism. Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in driving position are not included in the overall vehicle length of 16,500 mm. Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R17.5 3PMSF tyres at the manufacturer’s discretion. TPMS: TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface according to ISO 11992. For proper display, the towing vehicle must be capable of transmitting and displaying this data. Axles: BPW axles and suspension, 2 rigid axles, 1 trailing steering axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated by reverse gear and manually. Air suspension with lift and lower valve. Axle tools. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit. Electrical System: Electrical system complying with EU regulations, 24-volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicators. ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connections in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Manufactured from high-strength fine-grained steels. Steel grades: – S355J2+N / S355MC (yield strength 355 MPa) – S690QL / S700MC (yield strength 690 MPa) Curtain Body: Curtain body ??? 3,960 mm ??? – Galvanized front wall with tensioning system for sliding curtains. – "EDSCHA" brand roof, forward-sliding on ALU roof bow profiles (bolted to front and rear wall). – 3 pairs of sliding stakes in the loading area. – Rear of the body hydraulically extendable to left and right by approx. 750 mm. – Sliding roof with upwards foldable portal beam. – Sliding curtain with 700 mm length reserve, lashing straps approx. every 600 mm. – Height to upper edge of body approx. 3,960 mm (loaded). – Driving with open sliding roof is prohibited and will damage the curtain. Paintwork: Entire steel structure is automatically blast-cleaned with a wheel blasting machine after welding. Second blast treatment with corundum for optimal coating adhesion. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection. Final painting with 2 coats of 2K topcoat, single colour, shade of choice according to RAL system 841GL. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint.

Durumu: yeni, azami yük ağırlığı: 36.156 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, MAX200-N-3A-13.60-19.5-2.54 Technical Data Speed: 80 km/h Gross vehicle weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Tare weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Platform length: 13,600 mm Loaded fifth wheel height: 950–1,050 mm Swing clearance at rear: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360 / 1,405 mm Overall width: 2,540 mm Technical Description Ppedpfx Aeg Sk Tvsbkel Load platform: Load platform in extendable design with pneumatically operated locking mechanism. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of fold-out lashing rings (LC 5,000 daN). 2 pairs of fold-out lashing rings (LC 10,000 daN). Cut-outs in the outer frame of the platform for attaching tension straps (LC 2,000 daN). Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Axles: SAF axles: SAF CD axles, air-suspended, with disc brakes (377 mm), with lift/lower function (ET 120). Trailing steering axles with electro-magnetic reversing lock, activated via reverse gear or manually. Axle tools (± 80 kg). Brake system: Brake system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel structure made of high-strength fine-grain steels. Steel grades: S355J2+N / S355MC (yield strength 355 MPa) S690QL / S700MC (yield strength 690 MPa) Paintwork: Premium, long-lasting corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc-rich primer. High-quality two-component (2K) topcoat, single-colour, in RAL tones of your choice. Rear section metallised and painted in RAL 9010 (pure white). Metallic paint not available. Electrical system: Electrical system according to EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connector panel with sockets 24N, 24S & 15-pin. Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Standard accessories included: Yellow-red air couplings on the galvanised front connector panel. 2 wheel chocks with holders. 2" kingpin. Galvanised steel front wall, approx. 2,200 mm high (± 105 kg), EN12642-XL compliant. Yellow reflector tape according to EU regulations; fitted along the sides, on the extension, and the rear of the trailer. European reflective warning plates (red-yellow) at the rear of the trailer. Platform with approx. 38 mm hardwood floor (± 320 kg). 10 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the platform (± 30 kg). 1 spare wheel holder under the platform, right-hand side in direction of travel. Tyres 435/50 R 19.5, manufacturer’s choice. One mud flap at the rear of the trailer. Manual and documentation on USB stick. Bracket for rotating beacon at the rear of the trailer. At the gooseneck and rear panel, left and right, brackets for warning signs, incl. socket. One transverse INOX toolbox under the platform (1,000 x 400 x 250 mm) (± 135 kg). 6 pairs of WADER container locks in the platform for 1 x 20’ container, 2 x 20’ containers or 1 x 40’ container; an additional locking position provided in the extension for a 45’ container (± 90 kg). 4 pairs of WADER container locks (± 60 kg). 10 pairs of galvanised plug-in stakes approx. 100 x 50 mm, 1,000 mm high (± 220 kg). 3 pairs of crosswise stake pocket bars mounted in the platform for plug-in stakes 100 x 50 mm (± 95 kg). Storage for 1,000 mm plug-in stakes (± 45 kg). 1 spare wh

Durumu: yeni, azami yük ağırlığı: 44.000 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, Further information here: Podpfx Ajv D Abtsbkepl

Durumu: yeni, azami yük ağırlığı: 34.104 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2025, Further information here: Pjdpfxsv D Abgj Abkepl

Durumu: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, 3-axle MULTIMAX *PLUS low bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: * Loading platform width approx.: 2,540 mm Load height at max. payload approx.: 890 mm Suspension stroke approx.: -55/+145 mm Axle spacing: 1,360 mm *Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific regulations are exceeded. Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform, length approx. 9,600 mm with rear bevel approx. 900 mm x 6°. Loading platform behind gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating surface. Hydraulically foldable ramp tips. Ramps are individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward. Maximum load and approach angle as per technical data sheet: C470319 Maximum ramp angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift and lower valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF dual tyres. Manufacturer at our discretion. Load index 143/141J (144/144F) Ppedpfsizu Ntox Abkel Brake system: WABCO EBS-E braking system according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" configuration according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation). Entire steel structure shot-blasted, then hot-dip refined with ZINACOR 850 (zinc 85% - alu 15%). Painting 6-coat final treatment: Whole steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion promoter. Topcoat with 2 layers of 2-component (acrylic) paint, single-color to RAL palette as chosen, followed by sealing the cavities with special wax. Rims in silver. Multi-color and custom painting available at extra charge. Steel construction: High-strength fine-grained steel construction. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa). Welders certified to DIN EN 287-1. MAG welding process per EN ISO 4063. Shielding gas M21 per EN ISO 14175. Front wall made of steel, removable, approx. 400 mm high. Connection panel for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. 24N connection as per ISO-1185 24S connection as per ISO-3731 15-pin connection as per ISO-12098 If your pin assignment differs from the ISO standard, please inform us. "Anderson" socket on the front connection panel. Rema 78051-00 & Amp. 150 V. Cable for electric-hydraulic unit and/or electric winch (

Durumu: yeni, azami yük ağırlığı: 40.017 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Technical Description Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading Area: 5 pairs of fold-out lashing rings (LC 5,000 daN). 3 pairs of fold-out lashing rings (LC 10,000 daN). 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN). Hardwood flooring approx. 48 mm thick, tread-plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 205/65 R17.5, manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit is via the standardised EBS interface as per ISO 11992. For correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles: two fixed axles, two self-steering axles, air suspension, drum brakes, lifting/lowering function. The self-steering axles have electro-magnetic reverse lock, activated via reverse gear or manually. Axle tool included. Brake System: WABCO brake system compliant with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit. Electrical System: Electrical system as per EU regulations, 24 Volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights synchronise with the indicator. ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets. Connections in accordance with ISOs: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: Entire steel structure automatically shot blasted after welding using a shot blasting system. Second blasting treatment with corundum for optimum adhesion of the coating system. HRM metallisation of the complete chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection. Pedpfx Abjw Dl Hqskepl Final painting: two coats of 2-pack topcoat, single-colour in a shade of choice according to the RAL 841GL system. Rear section metallised and painted in RAL 9010 (pure white). Metallic finishes not available. Paint specification tested according to salt spray test ISO 9227-NSS. Cavity sealing with special wax. Options Included: 2'' kingpin One galvanised steel front wall. Yellow-red air couplings fitted to the galvanised front connection rail. 2 wheel chocks with holders on the front wall. Mountings at the rear of the gooseneck for ALU ramps. Further options available.

Durumu: kullanılmış, azami yük ağırlığı: 57.900 kg, toplam ağırlık: 73.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 06/2024, bir sonraki muayene (TÜV): 07/2026, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete stock of vehicles, including those available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Full equipment specification available upon request. Gooseneck: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm * Gooseneck rear with chamfer approx. 1,000 mm x 10° * Technical fifth-wheel load: 30,000 kg Suitable for tractors: 4x2, 6x2, and 6x4 Loading platform: * Telescopic loading platform, length approx. 8,800 mm, rear end chamfered approx. 500 mm x 10° Axles and Suspension: * BPW axles and suspension * 1st axle steered, with electro-magnetic reverse lock, all other axles hydraulically-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres: * 235/75 R 17.5 3PMSF twin tyres, load index 143/141J (144/144F) Braking System: * WABCO EBS-E braking system in accordance with EU regulations Paintwork: * Trailer colour: RAL 3002 Carmine Red Included accessories: * Plug-in steel front wall, approx. 400 mm high * Round NATO socket on front connection panel (Maeler & Kaege VG 96 917) * 3 kW electro-hydraulic power unit for hydraulic control (excludes hydraulic winches), without supply connection installation on the tractor unit * Parking position for warning boards on the gooseneck when not in use * 1 mounting adapter for spare wheel in front of the gooseneck bulkhead (without spare wheel) * External beam on the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from front, then every approx. 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of lying lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodized finish * 1 plug-in ALU rear board on the gooseneck, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor on the gooseneck, checker plate above the king pin * 2-inch king pin * Mechanical landing gear with 2-speed gearbox and crank JOST Modul B * Continuous hardwood flooring approx. 50 mm thick on the loading platform, interrupted between axles * Securing of the loading area with conically welded locking profiles approx. every 500 mm * Slotted holes for hook-in and repositionable bridging elements at the front of the loading platform * 1 sliding intermediate table, approx. 300 mm wide, for the extension pipe with large cross-section, with checker plate cover, front and rear with slotted holes for bridging elements * 1 pair lashing rings on the front cross member (LC 10,000 daN) * 7 pairs of recessed lashing rings foldable to the outside in the outer frame of the platform (LC 10,000 daN) * Bolt-on galvanised extensions, extendable by approx. 230 mm per side (without timber planks) * 1 pair of mechanical rear supports * Remote axle steering front and rear by cable remote control via push buttons, with single track monitoring of the axles, without installation in the tractor unit * Power cable for the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m in length) between trailer and tractor unit with NATO-NATO plug * 2 additional pairs of bolted lashing rings (LC 5,000 daN) Psdpfxsxuyprs Abkspl * 1 single-piece INOX toolbox, approx. 2,480 x 340 x 390 mm (L x W x H), straight design, with 2 external side doors and 1 top lid, located behind the bulkhead